How to install Hauppauge IRBlaster?

Henry_Castle · 2006-01-11, 10:06

To be honest, I have already read several times all the search in this forum and no success...I am missing!! I know MP includes a IRBlaster plugin for hauppauge.
I have Hauppauge PVR 150 (not MCE) that comes with IR Blaster...my idea is to control my STB with MP and get advantage of EPG service.
Somebody could give me some specific guide to install it.
Moreover, how does it work? My remote controls MP bt how to differentiate when I order to switch channel to my STB?
Thank you in advance!!!!
Henry_Castle

wewe · 2006-01-11, 11:12

Hi Henry_Castle,

I am using IRBlaster and its working. I am not able to receive EPG through the box (I think this you only can do with an inbuild PCI card).

See here how I installed IRBlaster:

1. switch on the "HCW IR Blaster" Plugin in MP Setup
2. Configure your remote control to work with the settop box using the IR Blaster Configuration Utility that came with your WinTV 150 (that step is independant from Mediaportal)
3. Add channels in Mediaportals channel setup:
3.1. Add channel and give it a name
3.2. Go to Tab "External", check "received by external settop box"
3.3. enter your input (CVBS#1 or SHVS [Attention: the names here do not work correctly, at lest for me, so try it out])
3.4. enter the Channel number for the box

that's it! (for sure you first have to install the Hardware like indicated in the doc of your WinTV150)

How it works? MP does everything for you. When you select channel 'abc' in MP which comes from the box and in there is channel 44 then MP sends a signal to the external box to switch to channel 44.

Tell me if you don't understand or if you have a specific problem.

thanks+regards
WeWe

Henry_Castle · 2006-01-12, 13:37

Thanks Wewe,
I assumed all about you said but unfortunately my STB is a M-Vision and IRBlaster software doesn't include this trademark of receiver. So I have to wait for un upgrade of hauppauge. Or perhaps I will look up for a third-party software.
Thanks,
Henry_Castle

Spif · 2006-01-12, 14:27

There is a good chance your set-top box uses codes that some other box uses. I would try different settings for cable, sattelite and region and then do a search for each setting to find the right codepage. That is how I found the working codes to my set-top box.

wewe · 2006-01-12, 17:30

same for me ... there is a 'test all'. You just need to wait until your STB reacts ...

thanks+regards
WeWe

2006-01-11, 10:06	#1 (permalink)
Henry_Castle Portal Member Join Date: Feb 2005 Posts: 10 Thanks: 0 Thanked 0 Times in 0 Posts	How to install Hauppauge IRBlaster? To be honest, I have already read several times all the search in this forum and no success...I am missing!! I know MP includes a IRBlaster plugin for hauppauge. I have Hauppauge PVR 150 (not MCE) that comes with IR Blaster...my idea is to control my STB with MP and get advantage of EPG service. Somebody could give me some specific guide to install it. Moreover, how does it work? My remote controls MP bt how to differentiate when I order to switch channel to my STB? Thank you in advance!!!! Henry_Castle

2006-01-11, 11:12	#2 (permalink)
wewe Portal Member Join Date: Aug 2005 Location: Herxheim Age: 47 Posts: 359 Thanks: 1 Thanked 0 Times in 0 Posts Country:	Hi Henry_Castle, I am using IRBlaster and its working. I am not able to receive EPG through the box (I think this you only can do with an inbuild PCI card). See here how I installed IRBlaster: 1. switch on the "HCW IR Blaster" Plugin in MP Setup 2. Configure your remote control to work with the settop box using the IR Blaster Configuration Utility that came with your WinTV 150 (that step is independant from Mediaportal) 3. Add channels in Mediaportals channel setup: 3.1. Add channel and give it a name 3.2. Go to Tab "External", check "received by external settop box" 3.3. enter your input (CVBS#1 or SHVS [Attention: the names here do not work correctly, at lest for me, so try it out]) 3.4. enter the Channel number for the box that's it! (for sure you first have to install the Hardware like indicated in the doc of your WinTV150) How it works? MP does everything for you. When you select channel 'abc' in MP which comes from the box and in there is channel 44 then MP sends a signal to the external box to switch to channel 44. Tell me if you don't understand or if you have a specific problem. thanks+regards WeWe __________________ Hard: ASUS K8M-VX, Sempron 3100+, MSI NX6200AX-TD256, Spinpoint SP2004C, WinTV PVR 150, MCE Remote + Keyboard / Soft: Win XP MCE, MP 0.2.1.0

2006-01-12, 17:30	#5 (permalink)
wewe Portal Member Join Date: Aug 2005 Location: Herxheim Age: 47 Posts: 359 Thanks: 1 Thanked 0 Times in 0 Posts Country:	same for me ... there is a 'test all'. You just need to wait until your STB reacts ... thanks+regards WeWe __________________ Hard: ASUS K8M-VX, Sempron 3100+, MSI NX6200AX-TD256, Spinpoint SP2004C, WinTV PVR 150, MCE Remote + Keyboard / Soft: Win XP MCE, MP 0.2.1.0

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Failed to start timeshifting Unable to create graph	Topher5000	General Support	31	2008-09-06 18:35
System freezes on digital TV channels with Hauppauge 1300 card.	regor007	General Support	16	2007-11-28 19:10
TV recording question/problem	'Arry	Installation, configuration support	9	2006-09-22 14:14
Recording from TV	'Arry	General Support	2	2006-09-20 01:12
Cant get MyTV to work (2.0 RC3)?	mdolan	General Support	3	2006-03-30 15:58

2006-01-12, 13:37	#3 (permalink)
Henry_Castle Portal Member Join Date: Feb 2005 Posts: 10 Thanks: 0 Thanked 0 Times in 0 Posts	Thanks Wewe, I assumed all about you said but unfortunately my STB is a M-Vision and IRBlaster software doesn't include this trademark of receiver. So I have to wait for un upgrade of hauppauge. Or perhaps I will look up for a third-party software. Thanks, Henry_Castle

2006-01-12, 14:27	#4 (permalink)
Spif Portal Member Join Date: Jan 2006 Location: Falun Age: 34 Posts: 29 Thanks: 0 Thanked 0 Times in 0 Posts Country: My System	There is a good chance your set-top box uses codes that some other box uses. I would try different settings for cable, sattelite and region and then do a search for each setting to find the right codepage. That is how I found the working codes to my set-top box.