[PATCH] Improvements for analog cards - Page 19

Frantid · 2009-01-02, 16:56

Is there any way to set the analog inputs of a hauppauge 250 to pal? My tuner is ntsc and tv server sets the inputs to match the tuner. However, I'm using a pal b, stb to watch tv. I use tv2 engine and it works perfectly, but I can't get tv server to work across reboots.

thanks.

Khurram · 2009-01-02, 19:49

Quote:

Originally Posted by Frantid

Is there any way to set the analog inputs of a hauppauge 250 to pal? My tuner is ntsc and tv server sets the inputs to match the tuner. However, I'm using a pal b, stb to watch tv. I use tv2 engine and it works perfectly, but I can't get tv server to work across reboots.

This and many other wonderful changes will be supported in 1.0.1 courtesy misterd. If you cant wait for it, then you can see page 16 ([PATCH] Improvements for analog cards) in this thread where I was having a similar problem and had to write some code for force PAL on my capture device. Its not hard to do once you read through misterd's posts on that page. Just make sure you make the call after constructing the graph but before you actually run it.

Frantid · 2009-01-03, 13:30

Khurram, thanks for the reply. I think I shall have to wait -- personally, I'm not much of a coder.

thanks again.

Olivier-h · 2009-01-06, 17:52

Hi,

Filter show ok now but still no audio/video on TerraTec HTC.
Is it normal I don't see the enoder setting for Cyberlink in MediaPOrtal config, intervideos one is showing???

wbr

misterd · 2009-01-06, 20:56

Hi,
it is normal that their is now configuration for the cyberlink encoders. We only have added support for the Intervideo encoders.

Some analog cards are only working when you use the right combination of encoders, muxer and settings. So you can only try the different available encoders and currently hope that starts working. Hopefully with one of the upcoming release this will be easier and more flexible.

MisterD

5Hundred · 2009-01-07, 21:17

looking forward to the new release misterd, if i can get the analogue side of my tv card to record in PAL i'll be delighted.

Thanks

2009-01-06, 17:52	#184 (permalink)
Olivier-h Portal Member Join Date: Sep 2004 Posts: 79 Thanks: 0 Thanked 0 Times in 0 Posts	Hi, Filter show ok now but still no audio/video on TerraTec HTC. Is it normal I don't see the enoder setting for Cyberlink in MediaPOrtal config, intervideos one is showing??? wbr Last edited by Olivier-h; 2009-01-06 at 18:51.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problems with several HW-encoding analog tuner cards	pbb	Development	3	2007-11-07 14:07
Are hardware-encoding analog cards supported?	pbb	Get Support	18	2007-07-01 22:16
Analog Channels Patch Italy!!!	fenomeno83	General Support	0	2006-10-17 02:17
Which analog capture cards does the mediaportal team use?	Richthofen	Hardware Selection Help	5	2006-09-08 22:41
[Patch] MultiTuner Bug with different PVR cards	FlipGer	General Development (no feature request here!)	12	2006-01-06 08:21

2009-01-02, 16:56	#181 (permalink)
Frantid Portal Member Join Date: Oct 2008 Posts: 61 Thanks: 6 Thanked 5 Times in 5 Posts Country: My System	Is there any way to set the analog inputs of a hauppauge 250 to pal? My tuner is ntsc and tv server sets the inputs to match the tuner. However, I'm using a pal b, stb to watch tv. I use tv2 engine and it works perfectly, but I can't get tv server to work across reboots. thanks.

2009-01-03, 13:30	#183 (permalink)
Frantid Portal Member Join Date: Oct 2008 Posts: 61 Thanks: 6 Thanked 5 Times in 5 Posts Country: My System	Khurram, thanks for the reply. I think I shall have to wait -- personally, I'm not much of a coder. thanks again.

2009-01-06, 20:56	#185 (permalink)
misterd Portal Developer Join Date: Apr 2006 Posts: 1,137 Thanks: 27 Thanked 38 Times in 26 Posts Country:	Hi, it is normal that their is now configuration for the cyberlink encoders. We only have added support for the Intervideo encoders. Some analog cards are only working when you use the right combination of encoders, muxer and settings. So you can only try the different available encoders and currently hope that starts working. Hopefully with one of the upcoming release this will be easier and more flexible. MisterD

2009-01-07, 21:17	#186 (permalink)
5Hundred Portal Member Join Date: Dec 2007 Posts: 156 Thanks: 3 Thanked 4 Times in 4 Posts Country: My System	looking forward to the new release misterd, if i can get the analogue side of my tv card to record in PAL i'll be delighted. Thanks