loosing data in EPG everyday... Sydney Australia

vvulture · 2007-12-02, 02:28

Hi all..
I am using xmltv plugin with TVE3 and latest SVN.
EPG data is pulled from ICE TV.

Now, when i import the data into xmltv, all is ok at first..
After a few hours, i always lose the data for channel seven, SBS and SBS2 ( No Data Available ).

If i re-import my xml file, it all comes good again for a few hours until i lose the data again for the same channels.

Any ideas as to what could be causing this ? I am using SQLExpress and never had this problem before..

TIA :-)

Marcusb · 2007-12-02, 04:21

I had similar issues in Melboure a little while ago.
I always have DTV EPG grab turned on, even though stations in Aust only show "Now and Next".
For some reason, after a while MP would ditch the xmltv data and try to load DTV EPG. Since there is only now and next, it meant lots of gaps. The cycle would repeat when I re-imported the XMLTV.

The solution was to turn off the DTV grabbing.

Hope this helps in your case

vvulture · 2007-12-02, 06:37

thanks Marcusb.. i'll give it a go..

I am assuming that you are talking about TVE3 --> General Settings --> EPG Tab and set EPG grabbing as unticked ( disabled ).

thanks again...

Marcusb · 2007-12-02, 06:54

yep. Good luck

2007-12-02, 02:28	#1 (permalink)
vvulture MP Donator Join Date: Jun 2006 Location: Sydney Age: 36 Posts: 268 Thanks: 5 Thanked 2 Times in 2 Posts Country: My System	loosing data in EPG everyday... Sydney Australia Hi all.. I am using xmltv plugin with TVE3 and latest SVN. EPG data is pulled from ICE TV. Now, when i import the data into xmltv, all is ok at first.. After a few hours, i always lose the data for channel seven, SBS and SBS2 ( No Data Available ). If i re-import my xml file, it all comes good again for a few hours until i lose the data again for the same channels. Any ideas as to what could be causing this ? I am using SQLExpress and never had this problem before.. TIA :-) __________________ Kids and computers do not mix...

2007-12-02, 06:37	#3 (permalink)
vvulture MP Donator Join Date: Jun 2006 Location: Sydney Age: 36 Posts: 268 Thanks: 5 Thanked 2 Times in 2 Posts Country: My System	thanks Marcusb.. i'll give it a go.. I am assuming that you are talking about TVE3 --> General Settings --> EPG Tab and set EPG grabbing as unticked ( disabled ). thanks again... __________________ Kids and computers do not mix...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Channel TEN Sydney Australia not working..	vvulture	Get Support	4	2007-11-22 07:08
EPG In Sydney Australia?	Lomax	Get Support	5	2007-05-20 07:34
Loosing Channel Data	nitro	support	0	2006-12-11 10:35
How to Setup EPG for Australia (Sydney)?	bigboss97	WebEPG	7	2006-05-23 13:08
Mixing DVB EPG grab with xmltv EPG data?	ziphnor	WebEPG	0	2006-02-19 12:54

2007-12-02, 04:21	#2 (permalink)
Marcusb Super Moderator Join Date: Feb 2005 Location: Melbourne Posts: 1,957 Thanks: 71 Thanked 28 Times in 28 Posts Country: My System	I had similar issues in Melboure a little while ago. I always have DTV EPG grab turned on, even though stations in Aust only show "Now and Next". For some reason, after a while MP would ditch the xmltv data and try to load DTV EPG. Since there is only now and next, it meant lots of gaps. The cycle would repeat when I re-imported the XMLTV. The solution was to turn off the DTV grabbing. Hope this helps in your case

2007-12-02, 06:54	#4 (permalink)
Marcusb Super Moderator Join Date: Feb 2005 Location: Melbourne Posts: 1,957 Thanks: 71 Thanked 28 Times in 28 Posts Country: My System	yep. Good luck