Report: Internal Radio with cinergy 600

tomtom21000 · 2004-06-22, 20:33

O.K. Here are my observations:

1. Autotune does not work. Sensity level does not influence this.
BTW: A "low" and "high" label to the sensitiy pannel might improve it

2. I can start a radio channel. It is displayed with correct name and running time in the topbar. I can switch channels.
And, that is strange: After switching channels I can here the radio for about one second or two, then it seems to be muted to zero sound. The sound level of the AC97 is still on normal level.

Conclusion: The internal player will work basically. There is only a little thing to be solved to get it fully working.

Any ideas about the observations?

tomtom21000

frodo · 2004-06-22, 20:41

sounds its muted indeed
You could check if all volume controls are set to 100% in the windows volume panel?

Frodo

tomtom21000 · 2004-06-24, 00:24

Sound on volume panel is on. It is a AC97 control panel.
It has an extra radio control which can be made visible in the settings. This is turned down to zero. But this is also the case with the axife player and with the radio soft that comes with the cinergy. And they both work with this setting.
Tuning up the radio volume slider results in permanent noise, even if no radio sw is active.

Can´t figure it out at the moment. mama wanted to test his cinergy with radio tomorrow. Maybe it works on his system. Let´s see.

tomtom21000

mama · 2004-06-24, 22:09

No way. It doesn´t work here too. I get error messages. The 22062004 seems to be more instable than the last version. myTV shows Pro7 and the info is ARD for example. If I switch to another channel (this button needs some workaround

) it plays the timeshiftcache of the last chan first. The OSD freezes sometimes and pausing or FF/RW causes freezes and stuttering TV. If I record, its shown as recorded, but neither the internal palyer nor the zplayer starts if I want to play it.

2004-06-22, 20:33	#1 (permalink)
tomtom21000 Retired Team Member Join Date: Apr 2004 Location: Germany Posts: 998 Thanks: 5 Thanked 6 Times in 6 Posts My System	Report: Internal Radio with cinergy 600 O.K. Here are my observations: 1. Autotune does not work. Sensity level does not influence this. BTW: A "low" and "high" label to the sensitiy pannel might improve it 2. I can start a radio channel. It is displayed with correct name and running time in the topbar. I can switch channels. And, that is strange: After switching channels I can here the radio for about one second or two, then it seems to be muted to zero sound. The sound level of the AC97 is still on normal level. Conclusion: The internal player will work basically. There is only a little thing to be solved to get it fully working. Any ideas about the observations? tomtom21000 __________________

2004-06-24, 00:24	#3 (permalink)
tomtom21000 Retired Team Member Join Date: Apr 2004 Location: Germany Posts: 998 Thanks: 5 Thanked 6 Times in 6 Posts My System	Sound on volume panel is on. It is a AC97 control panel. It has an extra radio control which can be made visible in the settings. This is turned down to zero. But this is also the case with the axife player and with the radio soft that comes with the cinergy. And they both work with this setting. Tuning up the radio volume slider results in permanent noise, even if no radio sw is active. Can´t figure it out at the moment. mama wanted to test his cinergy with radio tomorrow. Maybe it works on his system. Let´s see. tomtom21000 __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Failed to start timeshifting Unable to create graph	Topher5000	General Support	31	2008-09-06 17:35
KNC 1 DVB-C / cannot tune channels	lutz	General Support	15	2006-10-01 11:04
TV recording question/problem	'Arry	Installation, configuration support	9	2006-09-22 13:14
Recording from TV	'Arry	General Support	2	2006-09-20 00:12
TV and Radio channels on Cinergy DVB-S Card cause MP Crash	Joce	General Support	0	2006-06-09 23:43

2004-06-22, 20:41	#2 (permalink)
frodo Portal Developer Join Date: Apr 2004 Location: The Netherlands Age: 36 Posts: 1,516 Thanks: 3 Thanked 119 Times in 44 Posts Country: My System	sounds its muted indeed You could check if all volume controls are set to 100% in the windows volume panel? Frodo

2004-06-24, 22:09	#4 (permalink)
mama Portal Member Join Date: May 2004 Location: Germany Posts: 334 Thanks: 0 Thanked 0 Times in 0 Posts	No way. It doesn´t work here too. I get error messages. The 22062004 seems to be more instable than the last version. myTV shows Pro7 and the info is ARD for example. If I switch to another channel (this button needs some workaround ) it plays the timeshiftcache of the last chan first. The OSD freezes sometimes and pausing or FF/RW causes freezes and stuttering TV. If I record, its shown as recorded, but neither the internal palyer nor the zplayer starts if I want to play it.