Failed to start timeshifting Unable to create graph - Page 3

Meanman · 2006-06-13, 17:40

Quote:

Can you try to use the default codec's for MP (MPV for video & MPA for audio) in MP setup -> Television?

It did'nt work. Same result... only black screen when trying to watch the TV.
I tried to enable the digital part of the Hauppauge card again, and then I was back to the "Can not start timeshifing. Unable to create graph" message.
Seams like MP just want tune the chanels right..... Strange when I receive the channels fine with the bundle program :cry:

ronilse · 2006-06-13, 19:05

Hi,
Weird that the card doesn't work, have you tried to uninstall the card & re-add it with different drivers & without the bundled app?

It works very well here & i use this driver's, also tested on regular XP

If it is registry errors try to tun a clean program like CCleaner

Regards
Roy

Meanman · 2006-06-13, 21:30

OK ronilse,
I've now used CCleaner and removed all my video codecs, the Hauppauge bundle program and the Media Portal.
After this I restarted my comuter and installed the drivers you linked to. After this I reinstalled MP and updated it with the svn-build... Ran the setup wissard, but still no TV picture.
Here is what I get:

When I push the "TV on/off" button a red dot shows up and dissaper again in the checkbox to the right for the text.
:?:
The channels are assign to the analouge part of the card, Which is the pri1 card.

ronilse · 2006-06-13, 21:52

Hi,
This it's weird, i have the exact same tuner as you & MP supports both parts very well :?

You could try to run the HCWCLEAR.EXE in the drivers pack, this will clean all hauppauge reference from registry & reboot, after that it will install your card again (or you have to point it to the folder).

When you installed MP again, you did remove the MP folder (no old files)?

Regards
Roy

Topher5000 · 2006-06-13, 22:29

I got rid of the failed to start timeshifting... error by re-installing Avisynth, which was being used by ffdshow for post-processing. Don't know if this'll help.

Meanman · 2006-06-13, 23:21

Thopher5000,
I read your sollution on the problem earlier in the postings. Right now I do'nt have FFDshow installed at all, but I can try install an other version of what I have tried earlier.
This is'nt easy :wink:

JanArild · 2006-06-16, 21:03

Quote:

Originally Posted by Meanman

OK ronilse,
I've now used CCleaner and removed all my video codecs, the Hauppauge bundle program and the Media Portal.
After this I restarted my comuter and installed the drivers you linked to. After this I reinstalled MP and updated it with the svn-build... Ran the setup wissard, but still no TV picture.
Here is what I get:

When I push the "TV on/off" button a red dot shows up and dissaper again in the checkbox to the right for the text.
:?:
The channels are assign to the analouge part of the card, Which is the pri1 card.

Have the exact same problem. Tried everything mentioned here but no luck. Any ideas?????

Jan Arild

JanArild · 2006-06-16, 21:16

I think I solved the problem. Deleted the files under "My recordings" - "Card1" - "TempSBE".

When this was done everything worked perfect. :-)

Jan Arild

carreno · 2006-06-16, 21:26

Me too i have same problem with HVR1300.

apel444 · 2007-11-26, 16:15

I found this info.

All you need to do is get these files
sbe.dll
sbeio.dll
wmvcore2.dll

(you can find them at dlldump.com)

These should be put in your C:\windows\system32 directory

Then type these two lines into start/run or cmd.

regsvr32 sbe.dll

regsvr32 wmvcore2.dll

2007-11-26, 16:15	#30 (permalink)
apel444 Portal Member Join Date: Nov 2007 Posts: 5 Thanks: 0 Thanked 0 Times in 0 Posts	Worked for me I found this info. All you need to do is get these files sbe.dll sbeio.dll wmvcore2.dll (you can find them at dlldump.com) These should be put in your C:\windows\system32 directory Then type these two lines into start/run or cmd. regsvr32 sbe.dll regsvr32 wmvcore2.dll

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Autotune doesn't find any channels	friedit	Installation, configuration support	2	2007-01-02 14:34
no video from both DVD and TV	postema	Installation, configuration support	17	2006-12-05 22:09
Recording from TV	'Arry	General Support	2	2006-09-20 01:12
MP not picking up channels for Echostar 6,8 and 7 (Dishnet)	scapeone	The old Bugreport Forum	5	2006-03-24 20:41

2006-06-13, 19:05	#22 (permalink)
ronilse Portal Tester Join Date: Jul 2005 Posts: 3,209 Thanks: 19 Thanked 90 Times in 76 Posts Country: My System	Hi, Weird that the card doesn't work, have you tried to uninstall the card & re-add it with different drivers & without the bundled app? It works very well here & i use this driver's, also tested on regular XP If it is registry errors try to tun a clean program like CCleaner Regards Roy

2006-06-13, 21:30	#23 (permalink)
Meanman Portal Member Join Date: Jun 2006 Location: Oslo, Norway Posts: 9 Thanks: 0 Thanked 0 Times in 0 Posts	OK ronilse, I've now used CCleaner and removed all my video codecs, the Hauppauge bundle program and the Media Portal. After this I restarted my comuter and installed the drivers you linked to. After this I reinstalled MP and updated it with the svn-build... Ran the setup wissard, but still no TV picture. Here is what I get: When I push the "TV on/off" button a red dot shows up and dissaper again in the checkbox to the right for the text. :?: The channels are assign to the analouge part of the card, Which is the pri1 card.

2006-06-13, 21:52	#24 (permalink)
ronilse Portal Tester Join Date: Jul 2005 Posts: 3,209 Thanks: 19 Thanked 90 Times in 76 Posts Country: My System	Hi, This it's weird, i have the exact same tuner as you & MP supports both parts very well :? You could try to run the HCWCLEAR.EXE in the drivers pack, this will clean all hauppauge reference from registry & reboot, after that it will install your card again (or you have to point it to the folder). When you installed MP again, you did remove the MP folder (no old files)? Regards Roy

2006-06-13, 22:29	#25 (permalink)
Topher5000 Portal Member Join Date: Apr 2006 Posts: 158 Thanks: 0 Thanked 0 Times in 0 Posts	I got rid of the failed to start timeshifting... error by re-installing Avisynth, which was being used by ffdshow for post-processing. Don't know if this'll help.

2006-06-13, 23:21	#26 (permalink)
Meanman Portal Member Join Date: Jun 2006 Location: Oslo, Norway Posts: 9 Thanks: 0 Thanked 0 Times in 0 Posts	Thopher5000, I read your sollution on the problem earlier in the postings. Right now I do'nt have FFDshow installed at all, but I can try install an other version of what I have tried earlier. This is'nt easy :wink:

2006-06-16, 21:16	#28 (permalink)
JanArild Portal Member Join Date: Mar 2006 Location: Norway Posts: 30 Thanks: 1 Thanked 0 Times in 0 Posts	I think I solved the problem. Deleted the files under "My recordings" - "Card1" - "TempSBE". When this was done everything worked perfect. :-) Jan Arild

2006-06-16, 21:26	#29 (permalink)
carreno Portal Member Join Date: Jul 2005 Location: France Age: 21 Posts: 230 Thanks: 11 Thanked 17 Times in 7 Posts Country: My System	Me too i have same problem with HVR1300.