MP1 RC2 Not working right, resolution issues, no video

donnacha · 2008-08-03, 21:46

TV-Server Version: latest
MediaPortal Version: 1.0 RC2
MediaPortal Skin: AEON Wide
Windows Version: Xp sp3
CPU Type: P4 2.8ghz
HDD: 80g IDE
Memory: 1GB
Motherboard: Gigabyte
Video Card: AT1 2600 AGP
Video Card Driver: Catlyst 7.8
Sound Card: ASUS Xonar PCI
Sound Card AC3:
Sound Card Driver: latest asus
1. TV Card: TechnotrendUSB
1. TV Card Type: DVB-S
1. TV Card Driver: latest BDA
2. TV Card:
2. TV Card Type:
2. TV Card Driver:
3. TV Card:
3. TV Card Type:
3. TV Card Driver:
4. TV Card:
4. TV Card Type:
4. TV Card Driver:
MPEG2 Video Codec: NIVIDIA
MPEG2 Audio Codec: MPA
h.264 Video Codec: Cberlink PDVD8
Satelite/CableTV Provider: Freesat
HTPC Case: Silverstone LC17
Cooling: Kamakaze
Power Supply: 500w
Remote: ATI Remote Wonder
TV:HD projector
TV - HTPC Connection: VGA

Hello, I've just installed the latest version of MP and TV on a fresh windows XP install. After install, it loads up very slowly - what I mean is the graphics render very slow. Clicking a menu item takes ages and I hear the "click" before anything happens on screen. If I go into TV and TV starts to play then MP seems to recover and behave as normal. However once I shut down the TV or a video it revers back to a resolution of 800x600.

At the moment, I use 1280 x 720 to match my resolution but no video is shown at this resolution, just audi!

Log attached below.

Help greatly appreciated!!

Donnacha

Paranoid Delusion · 2008-08-03, 22:32

donnacha

If you use PDVD8 for Video and possibly FFDShow for audio, does it work then, nvidia has not been worked on for over 18 months, so not as good as PDVD8.
Or try the ATI codecs.

donnacha · 2008-08-04, 09:02

Paranoid Delusion, thanks for the response! I'll try your suggestions later. What is weird is that if I lower the resolution to match my monitor (1024 x 768), i.e. not my projector's resolution it seems to behave fine, and video is there, even when it the vidoe goes into the small viewing box!

The skin loads and plays fine in that resolution. Once I go back to 1280 x 720 it goes slow again, i.e. the screen takes a while to load and the navigation is slow.

Is it because the AEON Wide skin is set for a higher resolution than the one my Projector is set up for? Its when using that resolution that it also reverts to 800 x 600 when stopping a video. Its fine at the monitor resolution!

Thanks for any assistance

donnacha · 2008-08-05, 13:43

Quick update - I fiddled with the 3D settings on Catalyst control centre last night (don't know why, just did!). I ticked almost all the boxes, tried that and MP seemed to load and run perfectly!! I have force TV button checked in CCC as well, but it diverted back to 800 x 600 on one occasion, not every!

Does MP need any specific video 3D settings set?

Cheers

donnacha · 2008-08-10, 23:14

Final update - fixed!! I needed to add the resolutions to the TV Display Manager so that it wouldn't keep going back to 800 x 60 when a movie stopped. works fine for now, the odd crash excepted!!

Please mark as fixed and close thread

Regards

2008-08-03, 22:32	#2 (permalink)
Paranoid Delusion Super Moderator Join Date: Jun 2005 Location: Cheshire UK Posts: 5,939 Thanks: 107 Thanked 179 Times in 161 Posts Country: My System	donnacha If you use PDVD8 for Video and possibly FFDShow for audio, does it work then, nvidia has not been worked on for over 18 months, so not as good as PDVD8. Or try the ATI codecs. __________________ Ray\PD Check your codecs are fine with Filmerit. XP\Vista known issues FOR FULL SUPPORT PLEASE GIVE USER SPECIFICATIONS AND RELEVANT LOG's as per HERE

2008-08-04, 09:02	#3 (permalink)
donnacha Portal Member Join Date: Mar 2008 Location: York UK Posts: 9 Thanks: 0 Thanked 0 Times in 0 Posts Country:	Paranoid Delusion, thanks for the response! I'll try your suggestions later. What is weird is that if I lower the resolution to match my monitor (1024 x 768), i.e. not my projector's resolution it seems to behave fine, and video is there, even when it the vidoe goes into the small viewing box! The skin loads and plays fine in that resolution. Once I go back to 1280 x 720 it goes slow again, i.e. the screen takes a while to load and the navigation is slow. Is it because the AEON Wide skin is set for a higher resolution than the one my Projector is set up for? Its when using that resolution that it also reverts to 800 x 600 when stopping a video. Its fine at the monitor resolution! Thanks for any assistance Last edited by donnacha; 2008-08-04 at 16:48.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
MP1 RC2 single seat	medaust	MediaPortal 1 Talk	5	2008-07-30 04:22
Setup of MP1.0 ist not working for me	hanoota	Archive for pre RC3 version	19	2008-06-01 16:27
MP1 RC1 streaming IPTV issues.	MSMP	General Support	0	2008-04-26 19:19
Mediaportal don't switch the right video resolution after playing a video	jesterino	General Support	2	2007-10-25 16:52
tV guide and resolution issues please help	dank	General Support	2	2007-03-26 16:27

2008-08-05, 13:43	#4 (permalink)
donnacha Portal Member Join Date: Mar 2008 Location: York UK Posts: 9 Thanks: 0 Thanked 0 Times in 0 Posts Country:	Quick update - I fiddled with the 3D settings on Catalyst control centre last night (don't know why, just did!). I ticked almost all the boxes, tried that and MP seemed to load and run perfectly!! I have force TV button checked in CCC as well, but it diverted back to 800 x 600 on one occasion, not every! Does MP need any specific video 3D settings set? Cheers

2008-08-10, 23:14	#5 (permalink)
donnacha Portal Member Join Date: Mar 2008 Location: York UK Posts: 9 Thanks: 0 Thanked 0 Times in 0 Posts Country:	Final update - fixed!! I needed to add the resolutions to the TV Display Manager so that it wouldn't keep going back to 800 x 60 when a movie stopped. works fine for now, the odd crash excepted!! Please mark as fixed and close thread Regards