Updated AIW card support - Page 4

pindersk · 2006-10-09, 01:15

That is pretty neat! Too bad I get a blank screen, not even static shows. I think MP hates me!

SciDoctor · 2006-10-09, 11:57

With everything that you have done/achieved the software side looks not at fault.

This raises the question; is the hardware faulty?

Are you sure the AIW actualy works ?

What TV aerial signal are you feeding it ; analog or digital , FTA or Cable ?

Connect the svhs or composite inputs on the AIW to a suitable source ; do these work ?

pindersk · 2006-10-10, 00:37

I took the hardware out of a working Media Center Box so I do not believe it is that. I am hooking up analog cable (not over the air) to the computer. The Hauppauge gets the signal. I do not have the AIW media center software installed, but I can do that to see if I can watch TV through their program.

pindersk · 2006-10-11, 04:11

The AIW works with the ATI Media Center. Do you have any other ideas? Thanks!

pindersk · 2006-10-11, 05:16

I removed both TV cards and added the AIW first. Now video is displayed from the AIW but I have scrambled lines at the bottom of the video. Do not suppose you have a fix for that?

SciDoctor · 2006-10-11, 12:23

Good to know some progress.

I had thoughts it may be hardware problem .

The lines are to do with a filter setting that is incorrect.

A couple of things you can try .

In the channle setup in MP force your TV standard and don't have default for each channel.

Run the complete filter graph you have saved within graphedit and check each filter settings while playing (some filters have No settings) are suitable to your broadcast standard.

Choose your codec filters with care within MP for the TV, try a different deinterlace setting.

Marx · 2006-12-03, 20:36

Hello
I'm new on this forum and I'm trying to use AIW 9000 Pro with MP
I did everything suggested and it works, but processor works at 100% when i try to watch TV. This card supports DirectX9, but I don't know how to "switch on overlay" as suggested in one of threads. I don't use dual monitor setup, so I only have one primary display.
I did downgraded drivers, everything went ok. Channel scanning doesn't work but it's not problem for me because I know frequencies.
So how to lower CPU usage with MP and this card?

Marx · 2006-12-03, 22:34

Here is my crossbar:
http://www.kopernik.gliwice.pl/~marx/AIW9000.GIF
Error log:
2006-12-03 13:33:16 265 [ERROR] SinkGraphEx: RetryOtherInstances:6
2006-12-03 13:33:16 265 [ERROR] SinkGraphEx: find instances of :ATI TV Audio Crossbar instances
2006-12-03 13:33:16 265 [ERROR] SinkGraphEx: found :1 instances
2006-12-03 13:33:16 265 [ERROR] SinkGraphEx: try instance :0 @device:pnp:\\?\display#ntativxs35#5&2d51ac41&0&80 000005&01&00#{a799a801-a46d-11d0-a18c-00a02401dcd4}\global
2006-12-03 13:33:16 703 [ERROR] SinkGraphEx.SetupTeletext(): Failed to find WST Codec

Area: Media Portal Program
MediaPortal Version: 0.2.1.0 (2006-10-21)
MediaPortal Skin: BlueTwo
Windows Version: Windows XP (Dodatek SP2)
.NET CLR Version: 2.0.50727
DirectX Version: 4.09.00.0904 (9.0c)
Audio Codec: MPA Decoder Filter
Video Codec: MPV Decoder Filter
CPU Type: AMD Sempron 2600+
Memory: 1 GB
Motherboard: nForce (Gigabyte Technology Co., Ltd.)
TV Card Model: -
TV Card Type: -
TV Card Driver: -
Video Card Model: All-in-wonder 9000 (64 MB)
Video Card Driver: -
Video Card Resolution: 1280x1024
Video Render Type: -
Audio Card Model: Realtek AC'97 Audio
Audio Card Driver: -
Synopsis::

Marx · 2006-12-04, 20:53

ok great support

Now I know Radeon 9000 is only DirectX8. Is there possibility to use with MP and with lower CPU usage? ATI MMC works without problems, hovewer as I see it doesn't use crossbar

SciDoctor · 2006-12-04, 23:16

Unfortunatly not.

The AIW 9000 will struggle while the gui and video are displayed with a slower cpu. as the card is not fully DX9.

Fullscreen should be manageable as the GUI overheads drop to zero.

I use my AIW 9000 with a dual MP 2000, the GUI does struggle when the AIW tuned for TV even though there is plenty of CPU headroom. (60% of a single cpu is used)

100% cpu usage seem to high, try a diferent SVN release.

Try using the Cyberlink ATI decoders as they are better suited to the AIW

2006-12-03, 22:34	#38 (permalink)
Marx Portal Member Join Date: Dec 2006 Age: 36 Posts: 8 Thanks: 0 Thanked 0 Times in 0 Posts	Here is my crossbar: http://www.kopernik.gliwice.pl/~marx/AIW9000.GIF Error log: 2006-12-03 13:33:16 265 [ERROR] SinkGraphEx: RetryOtherInstances:6 2006-12-03 13:33:16 265 [ERROR] SinkGraphEx: find instances of :ATI TV Audio Crossbar instances 2006-12-03 13:33:16 265 [ERROR] SinkGraphEx: found :1 instances 2006-12-03 13:33:16 265 [ERROR] SinkGraphEx: try instance :0 @device:pnp:\\?\display#ntativxs35#5&2d51ac41&0&80 000005&01&00#{a799a801-a46d-11d0-a18c-00a02401dcd4}\global 2006-12-03 13:33:16 703 [ERROR] SinkGraphEx.SetupTeletext(): Failed to find WST Codec Area: Media Portal Program MediaPortal Version: 0.2.1.0 (2006-10-21) MediaPortal Skin: BlueTwo Windows Version: Windows XP (Dodatek SP2) .NET CLR Version: 2.0.50727 DirectX Version: 4.09.00.0904 (9.0c) Audio Codec: MPA Decoder Filter Video Codec: MPV Decoder Filter CPU Type: AMD Sempron 2600+ Memory: 1 GB Motherboard: nForce (Gigabyte Technology Co., Ltd.) TV Card Model: - TV Card Type: - TV Card Driver: - Video Card Model: All-in-wonder 9000 (64 MB) Video Card Driver: - Video Card Resolution: 1280x1024 Video Render Type: - Audio Card Model: Realtek AC'97 Audio Audio Card Driver: - Synopsis:: Last edited by Marx; 2006-12-03 at 23:25.

2006-12-04, 23:16	#40 (permalink)
SciDoctor Portal Tester Join Date: Feb 2005 Location: England Posts: 1,040 Thanks: 5 Thanked 8 Times in 8 Posts My System	Unfortunatly not. The AIW 9000 will struggle while the gui and video are displayed with a slower cpu. as the card is not fully DX9. Fullscreen should be manageable as the GUI overheads drop to zero. I use my AIW 9000 with a dual MP 2000, the GUI does struggle when the AIW tuned for TV even though there is plenty of CPU headroom. (60% of a single cpu is used) 100% cpu usage seem to high, try a diferent SVN release. Try using the Cyberlink ATI decoders as they are better suited to the AIW Last edited by SciDoctor; 2006-12-04 at 23:23.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
System requirements for HDTV with MediaPortal	Tech Geek	Hardware Selection Help	62	2007-08-08 08:20
Cant use Timeshifting or recording....	jojjal	Get Support	3	2007-01-03 20:58
TV recording question/problem	'Arry	Installation, configuration support	9	2006-09-22 14:14
Cant get MyTV to work (2.0 RC3)?	mdolan	General Support	3	2006-03-30 15:58

2006-10-09, 01:15	#31 (permalink)
pindersk Portal Member Join Date: Oct 2006 Posts: 21 Thanks: 0 Thanked 0 Times in 0 Posts Country:	That is pretty neat! Too bad I get a blank screen, not even static shows. I think MP hates me!

2006-10-09, 11:57	#32 (permalink)
SciDoctor Portal Tester Join Date: Feb 2005 Location: England Posts: 1,040 Thanks: 5 Thanked 8 Times in 8 Posts My System	With everything that you have done/achieved the software side looks not at fault. This raises the question; is the hardware faulty? Are you sure the AIW actualy works ? What TV aerial signal are you feeding it ; analog or digital , FTA or Cable ? Connect the svhs or composite inputs on the AIW to a suitable source ; do these work ?

2006-10-10, 00:37	#33 (permalink)
pindersk Portal Member Join Date: Oct 2006 Posts: 21 Thanks: 0 Thanked 0 Times in 0 Posts Country:	I took the hardware out of a working Media Center Box so I do not believe it is that. I am hooking up analog cable (not over the air) to the computer. The Hauppauge gets the signal. I do not have the AIW media center software installed, but I can do that to see if I can watch TV through their program.

2006-10-11, 04:11	#34 (permalink)
pindersk Portal Member Join Date: Oct 2006 Posts: 21 Thanks: 0 Thanked 0 Times in 0 Posts Country:	The AIW works with the ATI Media Center. Do you have any other ideas? Thanks!

2006-10-11, 05:16	#35 (permalink)
pindersk Portal Member Join Date: Oct 2006 Posts: 21 Thanks: 0 Thanked 0 Times in 0 Posts Country:	I removed both TV cards and added the AIW first. Now video is displayed from the AIW but I have scrambled lines at the bottom of the video. Do not suppose you have a fix for that?

2006-10-11, 12:23	#36 (permalink)
SciDoctor Portal Tester Join Date: Feb 2005 Location: England Posts: 1,040 Thanks: 5 Thanked 8 Times in 8 Posts My System	Good to know some progress. I had thoughts it may be hardware problem . The lines are to do with a filter setting that is incorrect. A couple of things you can try . In the channle setup in MP force your TV standard and don't have default for each channel. Run the complete filter graph you have saved within graphedit and check each filter settings while playing (some filters have No settings) are suitable to your broadcast standard. Choose your codec filters with care within MP for the TV, try a different deinterlace setting.

2006-12-03, 20:36	#37 (permalink)
Marx Portal Member Join Date: Dec 2006 Age: 36 Posts: 8 Thanks: 0 Thanked 0 Times in 0 Posts	Hello I'm new on this forum and I'm trying to use AIW 9000 Pro with MP I did everything suggested and it works, but processor works at 100% when i try to watch TV. This card supports DirectX9, but I don't know how to "switch on overlay" as suggested in one of threads. I don't use dual monitor setup, so I only have one primary display. I did downgraded drivers, everything went ok. Channel scanning doesn't work but it's not problem for me because I know frequencies. So how to lower CPU usage with MP and this card?

2006-12-04, 20:53	#39 (permalink)
Marx Portal Member Join Date: Dec 2006 Age: 36 Posts: 8 Thanks: 0 Thanked 0 Times in 0 Posts	ok great support Now I know Radeon 9000 is only DirectX8. Is there possibility to use with MP and with lower CPU usage? ATI MMC works without problems, hovewer as I see it doesn't use crossbar