Updated AIW card support - Page 6

krutknut · 2007-03-16, 23:52

Any plans for adding support for AIW 9200?

SciDoctor · 2007-03-17, 00:24

It is not so much the support within MP it IS whether the ATI drivers are either the T200 or WDM-NSP for the theatre 200 chipset on your card.

Also the ATI MCE encoder muct be instaled.

krutknut · 2007-03-17, 01:18

I see... the T200 or the WDM-NSP... No. Actually, I could use some help there. What are these things and what do I do with them? The TV works with ati tv, and with Got All Media, so it's not completely broken.
The ATI MCE encoder... again... where do I check that?
I like the interface of the Mediaportal. If I just could get the tv running as well...

krutknut · 2007-03-17, 03:22

I have the Omega Catalyst 38252. I don't really want to replace it. I need something more then?

krutknut · 2007-03-17, 03:47

Apparently, I also have an MCE Encoder. But there is no settings page where I could possibly use it. So there seems to be nothing seriously wrong with my system... or is there?

dave1215 · 2007-03-21, 02:07

I am having an issue with my AIW 2006 card. I have all the current drivers installed, but I keep getting the Error: "Unable to create graph for this device" Any help would be greatly appreciated

SciDoctor · 2007-03-22, 23:28

Post your logs from the MP folder as attachments.

dave1215 · 2007-03-22, 23:53

Ok attached you will find the LOG files.

Thanks

SciDoctor · 2007-04-03, 20:28

From an initial look of your logs.

It looks like the graph construct fails becaus the ATI MCE Encoders aren't installed.

RogueLegend · 2007-04-03, 22:14

Quote:

Originally Posted by SciDoctor

The encoder filters aren't required for the channel tuning, but MP will not work without them.

Try completing the initial setup, bypass the tv setup, and then when completed run the full config and try the set up from within there.

Ok, so I ran through the initial setup and bypassed the TV setup. When I go into the tv setup, I see several options for Audio/Video Codecs, including several options from ATI/Cyberlink, which indicates to me that the drivers are installed and functioning. However, when i go into the "Capture Cards" Section and try to edit, I still get the same "Unable to create graph for this device!!"

I don't know what you mean when you say "try the setup from within there." Is there something specific I am supposed to do/change? Should I try removing then re-adding the capture card? I'm hoping you can give me a few specific suggestions.

I have rechecked everything else at least five times or more at this point. I'm still hoping you can render some assistance.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
System requirements for HDTV with MediaPortal	Tech Geek	Hardware Selection Help	62	2007-08-08 08:20
Cant use Timeshifting or recording....	jojjal	Get Support	3	2007-01-03 20:58
TV recording question/problem	'Arry	Installation, configuration support	9	2006-09-22 14:14
Cant get MyTV to work (2.0 RC3)?	mdolan	General Support	3	2006-03-30 15:58

2007-03-16, 23:52	#51 (permalink)
krutknut Portal Member Join Date: Mar 2007 Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts	Any plans for adding support for AIW 9200?

2007-03-17, 00:24	#52 (permalink)
SciDoctor Portal Tester Join Date: Feb 2005 Location: England Posts: 1,040 Thanks: 5 Thanked 8 Times in 8 Posts My System	It is not so much the support within MP it IS whether the ATI drivers are either the T200 or WDM-NSP for the theatre 200 chipset on your card. Also the ATI MCE encoder muct be instaled.

2007-03-17, 01:18	#53 (permalink)
krutknut Portal Member Join Date: Mar 2007 Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts	I see... the T200 or the WDM-NSP... No. Actually, I could use some help there. What are these things and what do I do with them? The TV works with ati tv, and with Got All Media, so it's not completely broken. The ATI MCE encoder... again... where do I check that? I like the interface of the Mediaportal. If I just could get the tv running as well...

2007-03-17, 03:22	#54 (permalink)
krutknut Portal Member Join Date: Mar 2007 Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts	I have the Omega Catalyst 38252. I don't really want to replace it. I need something more then?

2007-03-17, 03:47	#55 (permalink)
krutknut Portal Member Join Date: Mar 2007 Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts	Apparently, I also have an MCE Encoder. But there is no settings page where I could possibly use it. So there seems to be nothing seriously wrong with my system... or is there?

2007-03-21, 02:07	#56 (permalink)
dave1215 Portal Member Join Date: Mar 2007 Age: 26 Posts: 12 Thanks: 0 Thanked 0 Times in 0 Posts Country:	I am having an issue with my AIW 2006 card. I have all the current drivers installed, but I keep getting the Error: "Unable to create graph for this device" Any help would be greatly appreciated

2007-03-22, 23:28	#57 (permalink)
SciDoctor Portal Tester Join Date: Feb 2005 Location: England Posts: 1,040 Thanks: 5 Thanked 8 Times in 8 Posts My System	Post your logs from the MP folder as attachments.

2007-03-22, 23:53	#58 (permalink)
dave1215 Portal Member Join Date: Mar 2007 Age: 26 Posts: 12 Thanks: 0 Thanked 0 Times in 0 Posts Country:	Ok attached you will find the LOG files. Thanks

2007-04-03, 20:28	#59 (permalink)
SciDoctor Portal Tester Join Date: Feb 2005 Location: England Posts: 1,040 Thanks: 5 Thanked 8 Times in 8 Posts My System	From an initial look of your logs. It looks like the graph construct fails becaus the ATI MCE Encoders aren't installed.