Problems wth floppyDTV after 2.0 RC 3

Tobbeswim · 2006-03-20, 12:03

The following problems have occurd after updating to RC3

Some channels are just black. Can not get them to work.
All channels on 602000 (QAM64) 6875 are hacking and slow.
I live in Denmark and use DVB-C from TDC SÃ¸nderjylland
Any solution?

hoberion · 2006-03-20, 13:21

I have the same unit, will rebuild my system tonight with rc3 and post my findings here..

hoberion · 2006-03-21, 00:19

still downloading sp2.. going to bed, will continue tomorrow

btw, I also am going to try the new beta firmware in combination with the hardware pid filter while im at it..

I think Frodo has the same setup....

if it works I might buy a second firedtv.. bit expensive though.. lol

hansdegit · 2006-03-24, 15:38

Where did you find the FloppyDTV beta-firmware?

MrMario64 · 2006-03-25, 13:37

be sure that the diseqc settings in MP are correct.
Due to a bug MP would set diseqc on Simple A.
Scanning will be fine, but zapping will cause black channels.

So edit your capturecard and check this setting.
Set to NONE when you do not have a diseqc switch.

petteram · 2006-03-27, 09:48

Beta firmware:
http://www.digital-everywhere.com/cm..._11_21_42.html

Anyone tested them yet?

hoberion · 2006-03-27, 14:20

I have, seem to be more stable, less signal loss and faster switching but it could also be the complete rebuild of my system.. havent seen a bug (yet)

dayn3779 · 2006-03-28, 01:25

I'm having the same blank screen with "no signal found' pop-up on cetain channels. Scanning is fine and some channels are OK.

How do I go about changing the diseqc settings you mention?

I'm using RC3 with the following CVS: mediaportal-cvs-03-26-2006--01-13

RC3 seems to be a real step change in stability and performance - lokking really good!

Many thanks,

Nathan

petteram · 2006-03-28, 09:50

Tried to install but, get error message"firesatApi.dll is missing"
Beta firmware "060306-FloppyDTV-C-CI-Rel-1-1-2-B31010"
Is this for MyTheatre only?

hoberion · 2006-03-28, 14:06

had the same issue but you need to copy it to system32 from the install.. (its in the bda driver)

/editfor clarity: the dll file I mean

2006-03-20, 12:03	#1 (permalink)
Tobbeswim Portal Member Join Date: Oct 2005 Posts: 14 Thanks: 0 Thanked 0 Times in 0 Posts	Problems wth floppyDTV after 2.0 RC 3 The following problems have occurd after updating to RC3 Some channels are just black. Can not get them to work. All channels on 602000 (QAM64) 6875 are hacking and slow. I live in Denmark and use DVB-C from TDC SÃ¸nderjylland Any solution?

2006-03-25, 13:37	#5 (permalink)
MrMario64 Retired Team Member Join Date: Apr 2004 Age: 34 Posts: 822 Thanks: 0 Thanked 0 Times in 0 Posts Country: My System	be sure that the diseqc settings in MP are correct. Due to a bug MP would set diseqc on Simple A. Scanning will be fine, but zapping will cause black channels. So edit your capturecard and check this setting. Set to NONE when you do not have a diseqc switch. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problems with floppydtv	Martin B	Get Support	2	2007-01-10 01:44
Stability problems - FireDTV / FloppyDTV (DVB-T and Boxer)	mcse	General Support	5	2006-10-05 14:30
still basic problems ...	wewe	The old Bugreport Forum	4	2006-08-13 07:42
EPIA VIA M-10000 Video Playback Problems	TylerDurden	Codecs, External Players	1	2006-07-23 18:50
Problems last 4~5 days with Astra19.2E (i.e. Dutch chan.)?	ronald2oo2	General Support	2	2006-05-21 16:22

2006-03-20, 13:21	#2 (permalink)
hoberion Portal Member Join Date: Feb 2006 Posts: 14 Thanks: 0 Thanked 0 Times in 0 Posts	I have the same unit, will rebuild my system tonight with rc3 and post my findings here..

2006-03-21, 00:19	#3 (permalink)
hoberion Portal Member Join Date: Feb 2006 Posts: 14 Thanks: 0 Thanked 0 Times in 0 Posts	still downloading sp2.. going to bed, will continue tomorrow btw, I also am going to try the new beta firmware in combination with the hardware pid filter while im at it.. I think Frodo has the same setup.... if it works I might buy a second firedtv.. bit expensive though.. lol

2006-03-24, 15:38	#4 (permalink)
hansdegit Portal Member Join Date: May 2005 Location: Schagen, The Netherlands Age: 36 Posts: 194 Thanks: 0 Thanked 0 Times in 0 Posts Country: My System	Where did you find the FloppyDTV beta-firmware?

2006-03-27, 09:48	#6 (permalink)
petteram Portal Member Join Date: Nov 2005 Location: Norway Age: 44 Posts: 191 Thanks: 0 Thanked 0 Times in 0 Posts	Beta firmware: http://www.digital-everywhere.com/cm..._11_21_42.html Anyone tested them yet?

2006-03-27, 14:20	#7 (permalink)
hoberion Portal Member Join Date: Feb 2006 Posts: 14 Thanks: 0 Thanked 0 Times in 0 Posts	I have, seem to be more stable, less signal loss and faster switching but it could also be the complete rebuild of my system.. havent seen a bug (yet)

2006-03-28, 01:25	#8 (permalink)
dayn3779 Portal Member Join Date: Aug 2005 Location: London Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts	I'm having the same blank screen with "no signal found' pop-up on cetain channels. Scanning is fine and some channels are OK. How do I go about changing the diseqc settings you mention? I'm using RC3 with the following CVS: mediaportal-cvs-03-26-2006--01-13 RC3 seems to be a real step change in stability and performance - lokking really good! Many thanks, Nathan

2006-03-28, 09:50	#9 (permalink)
petteram Portal Member Join Date: Nov 2005 Location: Norway Age: 44 Posts: 191 Thanks: 0 Thanked 0 Times in 0 Posts	Tried to install but, get error message"firesatApi.dll is missing" Beta firmware "060306-FloppyDTV-C-CI-Rel-1-1-2-B31010" Is this for MyTheatre only?

2006-03-28, 14:06	#10 (permalink)
hoberion Portal Member Join Date: Feb 2006 Posts: 14 Thanks: 0 Thanked 0 Times in 0 Posts	had the same issue but you need to copy it to system32 from the install.. (its in the bda driver) /editfor clarity: the dll file I mean