Question with MP and Hybrid cards

khalilmo · 2006-08-28, 07:16

I am a new user, so i do apologise for any ignorance. I have an issue where MP V 2.0.4 which i am running with my Divco Hybrid.
During setup MP automatically finds my Australian digital reception which is great, but I am actually trying to use the analog side due to me using a rebroad cast of Foxtel via the RF signal on the Digital foxtel box.
My Divco s/w finds both Digital and analoge and i can even select fom both.
I didn't think much of it but when i went looking for the configuration setting to turn off digital and use only analog, i was surprised, i have either not seen it or it is not there. How do i tell MP to only use Analog.

I am at a stand still with this issue. If anyone can help that would be great.

PHN2 · 2006-08-29, 17:05

Hi.
Try removing the digitalchannels in setup (not while running MP but under normal windows).

Per.

Marcusb · 2006-08-29, 17:29

With the hybrid cards they get added into MP as two separate cards.
In the TV card setup, try adding in a second card and see if an analog card is an option?

I don't think you can add an RF signal as external input. I think only RCA is an option there. If you have an AV input you'll get better quality anyway.

Analog software envoding cards are not all supported by MP. If the DVico doesn't get detected you may have to follow the steps in the stiky thread on the support forum. I'm pretty sure it is though.

khalilmo · 2006-09-15, 03:34

Sorry for the delay, do you mean from the Divco Software? This I have already done and no change.

khalilmo · 2006-09-15, 03:37

I can only get MP to detect 1 card not two, I may have to look into this sticky thread you are talking about.

Thanks,

fester88 · 2006-09-19, 07:32

I have a hybrid card too (Leadtek WinFast DTV2000 H) and can't figure out how to tune in the analog channels either. I followed the instructions in the sticky thread, submitted details for the card and was told it was supported. I took a look and found it in the supported cards under DVBt, but it is actually a hybrid card.

I tried adding it as another card, but it only recognises the one as digital.

Can anyone shed some light on this?

Thanks

fester88 · 2006-10-02, 07:51

*bump*

Can anyone tell me how to tune in analog channels in a hybrid card?

Any help would be much appreciated as I'm tearing me hair out at the moment trying to get it to work.

Thanks

Callifo · 2006-10-02, 09:07

Providing the card works fine, you should just have to do an autotune using the analogue card entry in setup.

fester88 · 2006-10-03, 03:31

It only shows the one card though, as digital. Tried to get it to look for other cards but still reports only the one.

Thanks for the suggestion though.

fester88 · 2006-11-29, 01:34

*bump*

Can anyone please help me with this as its driving me nuts! All I can watch is ABC and SBS (via DVB-T) and really really want to get analog up and running so that I can watch he other channels.

Any suggestions much appreciated!

2006-08-28, 07:16	#1 (permalink)
khalilmo Portal User Join Date: Aug 2006 Age: 35 Posts: 3 Thanks: 0 Thanked 0 Times in 0 Posts	Question with MP and Hybrid cards I am a new user, so i do apologise for any ignorance. I have an issue where MP V 2.0.4 which i am running with my Divco Hybrid. During setup MP automatically finds my Australian digital reception which is great, but I am actually trying to use the analog side due to me using a rebroad cast of Foxtel via the RF signal on the Digital foxtel box. My Divco s/w finds both Digital and analoge and i can even select fom both. I didn't think much of it but when i went looking for the configuration setting to turn off digital and use only analog, i was surprised, i have either not seen it or it is not there. How do i tell MP to only use Analog. I am at a stand still with this issue. If anyone can help that would be great.

2006-08-29, 17:05	#2 (permalink)
PHN2 Portal Member Join Date: Sep 2005 Location: Denmark Posts: 27 Thanks: 0 Thanked 0 Times in 0 Posts	Hi. Try removing the digitalchannels in setup (not while running MP but under normal windows). Per. __________________ Silverstone 14M with MCE remote, MSI K8N, 1 Gb ram, +3000 AMD, 6600 GT 128mb, M-audio Revo. 7.1, Firedtv-s with Viaskvat/T-rex super, Hauppauge hvr-1300, 300 gb Seagate, Liteon 165 dvd burner.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to setup Hybrid TvCards	frodo	Get Support	6	2008-11-30 21:59
Setting up hybrid cards - hauppauge hvr 3000?	tiwang	Get Support	7	2007-05-28 18:33
ASUSTeK lna Tiger Hybrid Capture Card not detected	9mand.dk	General Support	0	2006-08-14 21:12
DVB-T EPG on hybrid cards	xurr	General Support	1	2006-05-22 01:47
DNT DA2 Hybrid - Unable to create graph for this device	mcray	General Support	1	2006-01-20 18:51

2006-08-29, 17:29	#3 (permalink)
Marcusb Super Moderator Join Date: Feb 2005 Location: Melbourne Posts: 1,932 Thanks: 67 Thanked 28 Times in 28 Posts Country: My System	With the hybrid cards they get added into MP as two separate cards. In the TV card setup, try adding in a second card and see if an analog card is an option? I don't think you can add an RF signal as external input. I think only RCA is an option there. If you have an AV input you'll get better quality anyway. Analog software envoding cards are not all supported by MP. If the DVico doesn't get detected you may have to follow the steps in the stiky thread on the support forum. I'm pretty sure it is though.

2006-09-15, 03:34	#4 (permalink)
khalilmo Portal User Join Date: Aug 2006 Age: 35 Posts: 3 Thanks: 0 Thanked 0 Times in 0 Posts	Sorry for the delay, do you mean from the Divco Software? This I have already done and no change.

2006-09-15, 03:37	#5 (permalink)
khalilmo Portal User Join Date: Aug 2006 Age: 35 Posts: 3 Thanks: 0 Thanked 0 Times in 0 Posts	I can only get MP to detect 1 card not two, I may have to look into this sticky thread you are talking about. Thanks,

2006-09-19, 07:32	#6 (permalink)
fester88 Portal Member Join Date: Sep 2006 Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts Country:	I have a hybrid card too (Leadtek WinFast DTV2000 H) and can't figure out how to tune in the analog channels either. I followed the instructions in the sticky thread, submitted details for the card and was told it was supported. I took a look and found it in the supported cards under DVBt, but it is actually a hybrid card. I tried adding it as another card, but it only recognises the one as digital. Can anyone shed some light on this? Thanks

2006-10-02, 07:51	#7 (permalink)
fester88 Portal Member Join Date: Sep 2006 Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts Country:	bump Can anyone tell me how to tune in analog channels in a hybrid card? Any help would be much appreciated as I'm tearing me hair out at the moment trying to get it to work. Thanks

2006-10-02, 09:07	#8 (permalink)
Callifo Retired Team Member Join Date: Dec 2004 Location: Adelaide, Australia Age: 22 Posts: 1,444 Thanks: 0 Thanked 11 Times in 1 Post Country: My System	Providing the card works fine, you should just have to do an autotune using the analogue card entry in setup.

2006-10-03, 03:31	#9 (permalink)
fester88 Portal Member Join Date: Sep 2006 Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts Country:	It only shows the one card though, as digital. Tried to get it to look for other cards but still reports only the one. Thanks for the suggestion though.

2006-11-29, 01:34	#10 (permalink)
fester88 Portal Member Join Date: Sep 2006 Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts Country:	bump Can anyone please help me with this as its driving me nuts! All I can watch is ABC and SBS (via DVB-T) and really really want to get analog up and running so that I can watch he other channels. Any suggestions much appreciated!