Hauppauge WinTV Go Plus

asmod280672 · 2008-10-06, 17:46

Hi,

I´m a newbee using media portal. After installing the software I try to set up the tv-card (Hauppauge Win TV Go PCI), but I got an error message (unable to create graph). I found a lot of entries in google about the error message, but nothing special in combination with my tv-card. Driver version is 2.110.23339.0 and the card is 88x driver based. Are there anyone who have an idea, how to fix this problem? Thx a lot...

Greetings...

globaldonkey · 2008-10-07, 06:14

"Unable to start graph" is what you would get if you tried to actually turn TV on in MP and there was a problem. It's not an error you would see during setup, unless you were selecting the "preview" option in TV Server config.

Are you using TV Server or the inbuilt MP TV Engine? What version of MP are you running? Has MP detected the TV card?

AlfredENeuma · 2008-10-11, 17:53

Hi,

I have the same problem on a Hauppauge Nova-S-Plus.

I do not really have a solution, but for me the following workaround does the job:

Each time I restart the Tvserver, I go to the "TV-Server configuration", go to the Card-Setup and change the setting of the LNB by checking / unchecking the "Override default LNB frequencies".

After each change I go back to "TvChannels", this obviously does reinitialize the card.

Good luck

Alfred

2008-10-06, 17:46	#1 (permalink)
asmod280672 Portal User Join Date: Oct 2008 Posts: 1 Thanks: 0 Thanked 0 Times in 0 Posts	Hauppauge WinTV Go Plus Hi, I´m a newbee using media portal. After installing the software I try to set up the tv-card (Hauppauge Win TV Go PCI), but I got an error message (unable to create graph). I found a lot of entries in google about the error message, but nothing special in combination with my tv-card. Driver version is 2.110.23339.0 and the card is 88x driver based. Are there anyone who have an idea, how to fix this problem? Thx a lot... Greetings...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Hauppauge WinTV	Computergott	Media Portal - Allgemeines	27	2008-07-29 00:06
Kein TV -> Hauppauge WinTV PCI-FM bzw WinTV-GO-Plus	Flock1	Allgemein	2	2006-10-21 13:59
Hauppauge WinTV Go2	mabu	General Support	0	2006-07-12 16:22
wintv nova s (hauppauge)	imported_myzinsky	Allgemein	0	2006-05-24 12:32
Hauppauge wintv 500mce Wintv 350	J3Dante37	General Support	9	2005-11-06 23:12

2008-10-07, 06:14	#2 (permalink)
globaldonkey MP Donator Join Date: Apr 2007 Posts: 475 Thanks: 18 Thanked 16 Times in 14 Posts Country: My System	"Unable to start graph" is what you would get if you tried to actually turn TV on in MP and there was a problem. It's not an error you would see during setup, unless you were selecting the "preview" option in TV Server config. Are you using TV Server or the inbuilt MP TV Engine? What version of MP are you running? Has MP detected the TV card?

2008-10-11, 17:53	#3 (permalink)
AlfredENeuma Portal Member Join Date: Oct 2008 Posts: 166 Thanks: 12 Thanked 8 Times in 6 Posts Country: My System	Hi, I have the same problem on a Hauppauge Nova-S-Plus. I do not really have a solution, but for me the following workaround does the job: Each time I restart the Tvserver, I go to the "TV-Server configuration", go to the Card-Setup and change the setting of the LNB by checking / unchecking the "Override default LNB frequencies". After each change I go back to "TvChannels", this obviously does reinitialize the card. Good luck Alfred