MP 1.9/1.10 won't respond after sleep (1 Viewer)

Dark Eyes

Portal Pro
February 27, 2011
55
4
In MP 1.7.1 MP usually resumes from tray and is responsive after the PC has been in sleep mode. However, in MP 1.9 & 1.10, when the PC is restored from sleep, MP will restore from the tray, but it won't respond and the TV homepage shows the current program as whatever it was when it entered sleep. I have attached the log files from when it entered sleep at 00:27, it restored from the tray but was unresponsive and I terminated it (via Task Manager) at 08:37 and when it relaunched at 08:38.
If anybody is able to have a look at these and advise me of what you think the issue might be, then I would be very grateful, otherwise I will just have to go back to 1.7.1.

Let me know if you need any more information to help.
 

Attachments

  • MP unresponsive 050215.zip
    43.7 KB

azzuro

Test Group
  • Team MediaPortal
  • May 10, 2007
    9,948
    5,617
    France - IDF
    Home Country
    France France
    hello
    i have i think the same issue, but MP is not send to tray.
    can you use watchdog with the 1st option,
    Start TV
    Send HTPC to "standby mode"
    wait few sec/min after sleep is gone
    resume HTPC.
    and save the times, for know how many times te come back to MP homescreen.
     

    Dark Eyes

    Portal Pro
    February 27, 2011
    55
    4
    Hello azzuro,

    Apologies for the delay in getting around to doing this.
    I did the following;

    15:17 Start MP using Watchdog with option 1 selected
    15:18 Went to the TV section and set some recordings
    15:22 Returned to the TV home page, left MP fullscreen, put HTPC into sleep
    16:01 Woke HTPC from sleep, MP was still fullscreen, and after a short pause it was fully responsive.
    In case they are any use to you, I have attached the logs.

    I will repeat it, but with MP minimised to the tray before sleeping.
     

    Dark Eyes

    Portal Pro
    February 27, 2011
    55
    4
    This time I did the following;

    16:13 Start MP using Watchdog with option 1 selected
    16:17 Minimise MP to tray ans put HTPC into sleep
    16:56 HTPC woke itself up to do a scheduled recording.
    I restored MP from the tray, but it was unresponsive for over 5 mins and the time displayed was stuck at 16:16
    17:07 I tried to close MP from the fullscreen display, and by right-clicking exit from the icon in the tray, neither closed MP.
    17:08 I used Task Manager to end the MP process. Interestingly it did show a small amount of memory usage fluctuation for MP.

    I have uploaded the logs. Let me know if you need me to run any more tests and I will try and be swifter next time.
     

    Dark Eyes

    Portal Pro
    February 27, 2011
    55
    4
    Hello azzuro,

    Apologies for the delay in getting around to doing this.
    I did the following;

    13:48 Start MP using Watchdog with option 1 selected
    13:51 Went to the TV home page, minimised MP to the tray, put HTPC into sleep
    19:42 Woke HTPC from sleep, restored MP from tray, it was as usual unresponsive.
    In case they are any use to you, I have attached the logs.

    All were done with LAV filters as the TV codecs and MediaPortal Audio Render.
    I am reverting to MP 1.7.1 which works as expected.
     
    Last edited:

    Users who are viewing this thread

    Top Bottom