Get the ATI Remote Wonder up and running in 5 minutes flat!! - Page 2

hakuna · 2005-03-13, 11:19

Quote:

Originally Posted by Pablo99

Anyone know anything about using the new Remote Wonder Plus?
I have it partially working. Mostly I want to be able to launch MP with either Power, ATI, or TV button on the remote.

Did you try the plugin?
http://www.maisenbachers.de/dokuw/ho...nd_dvd_buttons

2005-03-15, 08:56

I tried the Plugin for MP that goes in the RW+ config. That works very nicely in MP. I tried following the instructions for the other one that configures the TV button, but it only breifly flashs a CMD window and will not run my batch file to start MP.

mPod · 2005-03-15, 11:42

Quote:

Originally Posted by Pablo99

but it only breifly flashs a CMD window and will not run my batch file to start MP.

Sounds like bad paths in your batch file. Make them absolute, not relative. Use variables like %ProgramFiles%. You can get a list of the used variables by typing "set" at a command prompt.

2005-03-16, 00:14

That was my first though, but if I click the batch file from explorer MP opens. When I press the TV button on the remote, it is apparently not running my batch file. I think I may have a clue. The plugin is named ATIMMC.exe (like Ati's MMC TV Player) MMC is not compatible with the new TV Wonder Elite, so I do not have that application installed. I suspect I should change the name of my plugin to match the exe for the Cyberlink PowerCinema. I think that is what is mapped by default to the TV Button on the Remote Wonder when the TV Wonder Elite is installed.

I'll try that when i get home tonight and let you know what happens.

2005-04-08, 07:12

so how did it work?

I have a RW elite and amtrying to figure out how to configure it to work with MP, but have had no sucess thus far.

any help would be appreciated.

2005-04-09, 04:56

Unfortunately no. I haven't been able to get it working either. I haven't had much time to play with it either.

Zamurai · 2006-10-12, 15:39

Hello, Im new with MP, started up with it yeasterday and been tweaking it all the time.

I own a Remote Wonder II but can't get it working properly, it's not X10 series remote so Key Master or Factory won't work with it... Is there some other way to get it fully functionable? Doing own configurations ain't a problem for me. If anyone has any ideas, please help me, thanks.

Wouldn't like to buy a new remote for this...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Dell Remote not recognized as an MCE remote	miguelal007	General Support	12	2007-10-06 22:13
MCE Remote Stopped Working in 0.2.0.2	colinsuk	The old Bugreport Forum	44	2006-10-04 21:18
MCE remote via IrTrans not working since RC3+cvn_15/04/06	guytpetj	The old Bugreport Forum	16	2006-09-12 19:38
ATI Remote Wonder II not working	WedgeCan	Installation, configuration support	11	2006-08-25 18:57
many problems	wallor	General Support	9	2005-12-13 10:06

2005-03-15, 08:56	#12 (permalink)
Pablo99 Guest Posts: n/a	I tried the Plugin for MP that goes in the RW+ config. That works very nicely in MP. I tried following the instructions for the other one that configures the TV button, but it only breifly flashs a CMD window and will not run my batch file to start MP.

2005-03-16, 00:14	#14 (permalink)
Pablo99 Guest Posts: n/a	That was my first though, but if I click the batch file from explorer MP opens. When I press the TV button on the remote, it is apparently not running my batch file. I think I may have a clue. The plugin is named ATIMMC.exe (like Ati's MMC TV Player) MMC is not compatible with the new TV Wonder Elite, so I do not have that application installed. I suspect I should change the name of my plugin to match the exe for the Cyberlink PowerCinema. I think that is what is mapped by default to the TV Button on the Remote Wonder when the TV Wonder Elite is installed. I'll try that when i get home tonight and let you know what happens.

2005-04-08, 07:12	#15 (permalink)
Anonymous Guest Posts: n/a	so how did it work? I have a RW elite and amtrying to figure out how to configure it to work with MP, but have had no sucess thus far. any help would be appreciated.

2005-04-09, 04:56	#16 (permalink)
Pablo99 Guest Posts: n/a	Unfortunately no. I haven't been able to get it working either. I haven't had much time to play with it either.

2006-10-12, 15:39	#17 (permalink)
Zamurai Portal User Join Date: Oct 2006 Age: 21 Posts: 2 Thanks: 0 Thanked 0 Times in 0 Posts Country:	Hello, Im new with MP, started up with it yeasterday and been tweaking it all the time. I own a Remote Wonder II but can't get it working properly, it's not X10 series remote so Key Master or Factory won't work with it... Is there some other way to get it fully functionable? Doing own configurations ain't a problem for me. If anyone has any ideas, please help me, thanks. Wouldn't like to buy a new remote for this...