Crashes with Mpeg2dec en Intervideo when opening MyTV (1 Viewer)

richber

Portal Member
December 11, 2005
14
0
Area: Media Portal Program
MediaPortal Version: 0.2.0.0 RC2 (2005-12-16)
MediaPortal Skin: X-Mas 2005
Windows Version: Windows XP (SP2)
.NET CLR Version: 2.0.50727
DirectX Version: 4.09.00.0904 (9.0c)
Audio Codec: MPEG/AC3/DTS/LPCM Audio Decoder
Video Codec: DScaler Mpeg2 Video Decoder
CPU Type: AMD Athlon 64 3200+
Memory: 1 GB
Motherboard: nForce3
TV Card Model: Club3D ZAP1000
TV Card Type: Hardware
TV Card Driver: latest
Video Card Model: Gigabyte Radeon 9600 Pro (256 MB)
Video Card Driver: latest
Video Card Resolution: 1024x768
Video Render Type: VMR9
Audio Card Model: Creative Audigy Audio Processor (WDM)
Audio Card Driver: latest
Synopsis:: -

After a complete new install of my computer I had to install MP also again.
When I first started MP and I tried to open MyTV I got a crash with the following Windows Logbook message (with the source: .NET Runtime 2.0 Error):
Faulting application mediaportal.exe, version 0.0.0.0, stamp 43a3e657, faulting module mpeg2decfilter.ax, version 1.0.0.0, stamp 426d4e3b, debug? 0, fault address 0x0001c601.

So I changed to the Intervideo decoder, which results in the following message:
Faulting application mediaportal.exe, version 0.0.0.0, stamp 43a3e657, faulting module ivivideo.ax, version 7.0.27.130, stamp 43707b3a, debug? 0, fault address 0x00009b3c.

After that I changed to the DScaler decoder and up till now MyTV and the Radio works.

Does anybody have any idea what went wrong and are there any solutions, especially because the
Intervideo decoder is havenly recommended on this forum?

BTW, Frodo once wrote
Actually, the best mpeg2 codec i found is the Intervideo mpeg2 codecs which come with WinDVD 6
I still only can fiend the version 7.x. Does anybody know where the version 6 is to become?

Thnx i.a.
 

richber

Portal Member
December 11, 2005
14
0
Callifo said:
Intervideo windvd 7 works just as well as 6 or you could try the Nvidia codecs as well.
As I mentioned in my early message:
richber said:
Faulting application mediaportal.exe, version 0.0.0.0, stamp 43a3e657, faulting module ivivideo.ax, version 7.0.27.130, stamp 43707b3a, debug? 0, fault address 0x00009b3c.
The module ivivideo.ax is the WinDVD 7 videodecoder and my machine crashed on that :cry:. Tonight I will try both decoders again en see if my computer still crashes on them.
 

smithft

Portal Member
November 18, 2005
11
0
Club3D ZAP1000 and Radio

Hi richber,
I am interested in buying a ZAP1000 and have a question on the radio side. I see you seem to have got it working but the capture card reference page https://www.team-mediaportal.com/dokuw/install/capturecards/start says n/a against Radio for that Card. The page translates n/a as "n/a - not applicable (card does not have this functionality)"

I have checked the spec of the card and it says it does have radio.
Can you confirm that it does have Radio and you got it working and if so is it just a small error on the Capture Cards reference page.

I am also using the latest release 0.1.3 if that makes any difference

Thanks
Frank
 

richber

Portal Member
December 11, 2005
14
0
Re: Club3D ZAP1000 and Radio

smithft said:
I have checked the spec of the card and it says it does have radio.
Can you confirm that it does have Radio and you got it working and if so is it just a small error on the Capture Cards reference page.

Yes, is does have radio and it wordks quit well.

smithft said:
I am also using the latest release 0.1.3 if that makes any difference

I'am using version 0.2.0.0 RC2
 

Users who are viewing this thread

Similar threads

Sorry for the late response. In my experience, the EPG grabbing of a single transponder takes 2 to 3 minutes. Afterwards it takes 1 to 2 minutes to write the data to disk. To speed up the EPG stuff (not only writing but also reading the EPG guide in MediaPortal), I changed the program table (and only that table) from InnoDB to...
Sorry for the late response. In my experience, the EPG grabbing of a single transponder takes 2 to 3 minutes. Afterwards it takes...
I get a few "Continuity error..." after the EPG scan finished: [2021-01-30 18:56:10,278] [4c45530] [18c8] - mhw reset [2021-01-30...
Replies
2
Views
1K
Anecdotal testimonies are not helpful. If you guys would like to continue this chat, I'll move this thread to the Café section. The discussion about your issues is taking place here: Installation failing
Anecdotal testimonies are not helpful. If you guys would like to continue this chat, I'll move this thread to the Café section...
I have been looking for a replacement to Windows Media Center for a little over a year.No luck. Now, I'm no Microsoft fanboy, but I...
Replies
15
Views
3K
Dear Morpheus_xx, I still assume that the issue is not due to hardware problems. In the beginning of my search I thought, I would need to dig into the registry, but eventually found out that GraphStudio can in principle also change the merit of decoders. As a first step I attempted to alter the Microsoft DTV-DVD A/V Decoders, but...
Dear Morpheus_xx, I still assume that the issue is not due to hardware problems. In the beginning of my search I thought, I would...
MediaPortal Version: MediaPortal 2 Summer '15 Update 1 Release Windows Version: Windows 7 Ultimate x64 SP1 CPU Type: Intel i3-2105...
Replies
14
Views
3K
hi, just in case issue returns again, you may also try to reinstall LAV (simple install over, or deinstall+install again, you can also try downgrade and re-upgrade). i remebering that some filter-graphs sometimes hangs for a while after playback under some rare conditions, preventing next file to be played. regards.
hi, just in case issue returns again, you may also try to reinstall LAV (simple install over, or deinstall+install again, you can...
Hi, As the topic describes, when I have watched a video from MP-TVSeries and tries to watch a second one the screen goes black. If...
Replies
8
Views
1K
Okay, no problem. At least we know that there was no problem with TV Server because the new CAM works. Marking thread as "no bug"...
Okay, no problem. At least we know that there was no problem with TV Server because the new CAM works. Marking thread as "no bug"...
MediaPortal Version: 1.15.0 Description I've just added a CAM to my Technotrend c-1501 on a well-working system (w10, asus...
Replies
5
Views
2K
Top Bottom