Area: MyTV
MP Version: 0.2.0.3
Skin: Project Mayhem III
Windows Version: XP MCE 2005 (SP2 and all critical updates)
CPU Type: Pentium 4 (2.4Ghz)
Memory: 1GB RAMBUS
Motherboard Chipset: Intel i850
Video Card: Nvidia GeForce 6800 GT
Video Card Driver: 8.1.9.8
Video Card Resolution: 800 x 600
Video Render Type: VMR9
Video Codec Type & Version: Nvidia PureVideo Decoder
Audio Codec Type & Version: Nvidia Audio Decoder
TV Card: WinTV PVR-150MCE, Hauppauge
TV Card Type: Hardware
TV Card Driver: 2.0.30.23074
Optional Log: N/A
Optional References: https://forum.team-mediaportal.com/viewtopic.php?t=15531
https://forum.team-mediaportal.com/viewtopic.php?t=17039
https://forum.team-mediaportal.com/viewtopic.php?t=12230
Synopsis: Can't get Myblaster plugin to change channels on my STB (Dish Network 311). I mentioned some of the many threads which I have read and still have no luck. I would really like to scrap MCE 2005 and use MP as it appears to be SO much better. Of course, if I can't change the channels with my remote, what's the point?
Here is what I have done so far...Used Zap2it plugin to populate the channels (worked flawlessly) and all channels are set as external (received through settop, and SVHS). Downloaded and installed myblaster plugin (dll in process folder and blaster.exe in MP folder). Ran blaster.exe and learned the codes for my Dish 311 STB. I made sure MyBlaster plugin was enabled.
MP doesn't change the channels (the channels are working because I am able to tune them with Dish remote.) I then ran blaster.exe again and made sure the codes were learned for port two. I edited the mediaportal.xml to force port 2. When I select a different channel through guide, I see the bud flash, but the channel stays the same.
Is there a good reference manual for getting this setup? I have reviewed the wiki, but it seems very limited at this point. I'm about to give up on this altogether because it is more frustrating than it is worth. I would appreciate any assistance.
MP Version: 0.2.0.3
Skin: Project Mayhem III
Windows Version: XP MCE 2005 (SP2 and all critical updates)
CPU Type: Pentium 4 (2.4Ghz)
Memory: 1GB RAMBUS
Motherboard Chipset: Intel i850
Video Card: Nvidia GeForce 6800 GT
Video Card Driver: 8.1.9.8
Video Card Resolution: 800 x 600
Video Render Type: VMR9
Video Codec Type & Version: Nvidia PureVideo Decoder
Audio Codec Type & Version: Nvidia Audio Decoder
TV Card: WinTV PVR-150MCE, Hauppauge
TV Card Type: Hardware
TV Card Driver: 2.0.30.23074
Optional Log: N/A
Optional References: https://forum.team-mediaportal.com/viewtopic.php?t=15531
https://forum.team-mediaportal.com/viewtopic.php?t=17039
https://forum.team-mediaportal.com/viewtopic.php?t=12230
Synopsis: Can't get Myblaster plugin to change channels on my STB (Dish Network 311). I mentioned some of the many threads which I have read and still have no luck. I would really like to scrap MCE 2005 and use MP as it appears to be SO much better. Of course, if I can't change the channels with my remote, what's the point?
Here is what I have done so far...Used Zap2it plugin to populate the channels (worked flawlessly) and all channels are set as external (received through settop, and SVHS). Downloaded and installed myblaster plugin (dll in process folder and blaster.exe in MP folder). Ran blaster.exe and learned the codes for my Dish 311 STB. I made sure MyBlaster plugin was enabled.
MP doesn't change the channels (the channels are working because I am able to tune them with Dish remote.) I then ran blaster.exe again and made sure the codes were learned for port two. I edited the mediaportal.xml to force port 2. When I select a different channel through guide, I see the bud flash, but the channel stays the same.
Is there a good reference manual for getting this setup? I have reviewed the wiki, but it seems very limited at this point. I'm about to give up on this altogether because it is more frustrating than it is worth. I would appreciate any assistance.