Reply to thread

Message

Clicking "yes" makes it start the service, both when running SetupTv from the debug folder and from the 1.12 install. If I stop the new process, SetupTv just complains that the TV service is not started.

I will try to comment out the section you refer to later today.

I have run MSBUILD_Rebuild_All_MediaPortal_Debug.bat without errors. Doesn't it build everything for debugging?

Maybe another approach would be better:

I'm trying to get the Hauppauge HVR-2200 dual DVBT/analog card to complete analog tuning. After finding a random number of channels it BSODs with "Page fault in non-paged area" in ntoskrnl.exe. After reboot, MP2 manages to use the channels registered before the BSOD but the sound (and possibly image) stutter. When closing MP2 it BSODs. Please note that I am sticking to MP1 at this point - MP2 was just to see if there were any changes that might affect this problem.

I have tested this HVR-2200 card with WinTV7 so I know that it isn't broken. I am also successfully running another MP1.12 machine with a Compro Videomate Vista E900F that is a very similar card. The machine I am using now has only had the HVR-2200, so it can't be a driver conflict.

The HVR-2200 successfully completes FM radio tuning and playing. It also completes analog TV tuning if the cable is not attached (so no channel is found).

Is there a better way to debug this problem than what I have tried so far?

<blockquote data-quote="Kimmeridgien" data-source="post: 1157795" data-attributes="member: 60361">Clicking &quot;yes&quot; makes it start the service, both when running SetupTv from the debug folder and from the 1.12 install. If I stop the new process, SetupTv just complains that the TV service is not started.I will try to comment out the section you refer to later today.I have run MSBUILD_Rebuild_All_MediaPortal_Debug.bat without errors. Doesn't it build everything for debugging?Maybe another approach would be better:I'm trying to get the Hauppauge HVR-2200 dual DVBT/analog card to complete analog tuning. After finding a random number of channels it BSODs with &quot;Page fault in non-paged area&quot; in ntoskrnl.exe. After reboot, MP2 manages to use the channels registered before the BSOD but the sound (and possibly image) stutter. When closing MP2 it BSODs. Please note that I am sticking to MP1 at this point - MP2 was just to see if there were any changes that might affect this problem.I have tested this HVR-2200 card with WinTV7 so I know that it isn't broken. I am also successfully running another MP1.12 machine with a Compro Videomate Vista E900F that is a very similar card. The machine I am using now has only had the HVR-2200, so it can't be a driver conflict. The HVR-2200 successfully completes FM radio tuning and playing. It also completes analog TV tuning if the cable is not attached (so no channel is found).Is there a better way to debug this problem than what I have tried so far?</blockquote>

[QUOTE="Kimmeridgien, post: 1157795, member: 60361"] Clicking "yes" makes it start the service, both when running SetupTv from the debug folder and from the 1.12 install. If I stop the new process, SetupTv just complains that the TV service is not started. I will try to comment out the section you refer to later today. I have run MSBUILD_Rebuild_All_MediaPortal_Debug.bat without errors. Doesn't it build everything for debugging? Maybe another approach would be better: I'm trying to get the Hauppauge HVR-2200 dual DVBT/analog card to complete analog tuning. After finding a random number of channels it BSODs with "Page fault in non-paged area" in ntoskrnl.exe. After reboot, MP2 manages to use the channels registered before the BSOD but the sound (and possibly image) stutter. When closing MP2 it BSODs. Please note that I am sticking to MP1 at this point - MP2 was just to see if there were any changes that might affect this problem. I have tested this HVR-2200 card with WinTV7 so I know that it isn't broken. I am also successfully running another MP1.12 machine with a Compro Videomate Vista E900F that is a very similar card. The machine I am using now has only had the HVR-2200, so it can't be a driver conflict. The HVR-2200 successfully completes FM radio tuning and playing. It also completes analog TV tuning if the cable is not attached (so no channel is found). Is there a better way to debug this problem than what I have tried so far? [/QUOTE]