Reply to thread

Message

<blockquote data-quote="ColinT" data-source="post: 668454" data-attributes="member: 29886">I apologise. I used the TVLibrary MP 1.1 patch, as MP1.1.1 screwed up my set up so I I have reverted to MP1.1Tuner 6 is connected (with no Diseqc)&nbsp; directly to LNB which pints to Astra2 (28)Tuner 7 is connected via Diseqc to Hotbird (13) Astra 1 (19) and Astra 2 (28) I am never certain of the switch positions (MP forgets them)My Hauppage card&nbsp; (I think) is on Tuner 9The DVBT tuning attempts are for EPG downloads. I had not reconfigured these cards for the test.&nbsp;For the test I disabled tuners 6 and 9 and then tried to select pre-allocated&nbsp; channels using tuner7 on different satellites (BBC HD, TV5MONDE FBS, Harmonic Canal 24 Horas. As this was unsuccessful, I re-enabled tuner 6 (which has a higher priority than port 7) to check it was still working.On MP as far as I know it is difficult to have cards with different Diseqc setups, my tuner 6 uses the same settings as tuner 7, but I have only mapped the channels fro ASTRA2 that I use for it. Whilst the diseqc commands are sent, they are irrelevent, as there is no switch.SO.... it is only card 7 channel changes attempts which were the valid test tunes. I also tried to tune scan tuner 7 to each of the satelites, but got no signals.I didnt have a whole lot of time for the test.After the test, I re-plugged up my Hauppauge tuner, and everything is still working.On all the tuning attempts I am getting &quot;No signal&quot; rather than the &quot;Unknown Error&quot; that I was getting after I blew my card.Hope this helpsColin T <img src="data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7" class="smilie smilie--sprite smilie--sprite5" alt=":confused:" title="Confused&nbsp; &nbsp; :confused:" loading="lazy" data-shortname=":confused:" /></blockquote>

[QUOTE="ColinT, post: 668454, member: 29886"] I apologise. I used the TVLibrary MP 1.1 patch, as MP1.1.1 screwed up my set up so I I have reverted to MP1.1 Tuner 6 is connected (with no Diseqc) directly to LNB which pints to Astra2 (28) Tuner 7 is connected via Diseqc to Hotbird (13) Astra 1 (19) and Astra 2 (28) I am never certain of the switch positions (MP forgets them) My Hauppage card (I think) is on Tuner 9 The DVBT tuning attempts are for EPG downloads. I had not reconfigured these cards for the test. For the test I disabled tuners 6 and 9 and then tried to select pre-allocated channels using tuner7 on different satellites (BBC HD, TV5MONDE FBS, Harmonic Canal 24 Horas. As this was unsuccessful, I re-enabled tuner 6 (which has a higher priority than port 7) to check it was still working. On MP as far as I know it is difficult to have cards with different Diseqc setups, my tuner 6 uses the same settings as tuner 7, but I have only mapped the channels fro ASTRA2 that I use for it. Whilst the diseqc commands are sent, they are irrelevent, as there is no switch. SO.... it is only card 7 channel changes attempts which were the valid test tunes. I also tried to tune scan tuner 7 to each of the satelites, but got no signals. I didnt have a whole lot of time for the test. After the test, I re-plugged up my Hauppauge tuner, and everything is still working. On all the tuning attempts I am getting "No signal" rather than the "Unknown Error" that I was getting after I blew my card. Hope this helps Colin T :S [/QUOTE]

Verification