Reply to thread

Message

ok I see I was meant to put the ID at the end. Like this:

[CODE]
#dvbtune -f 1183000 -p h -tone 0 -s 22500 && ./rb-download -v -b /home/rhys/tvnzmheg -f channels.conf 1035
Using DVB card "ST STV0299 DVB-S"
tuning DVB-S to L-Band:0, Pol:H Srate=22500000, 22kHz=off
polling....
Getting frontend event
FE_STATUS:
polling....
Getting frontend event
FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
Bit error rate: 3554
Signal strength: 55668
SNR: 59361
FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
Trying to open channels.conf
TODO: Only able to tune DVB-T devices at present
Unable to retune; let's hope you're already tuned to the right frequency...
Unable to find Carousel Descriptor in PMT
[/CODE]

"Unable to find Carousel Descriptor in PMT"
Any ideas what might casue this?
Cheers,
Rhys
...Rebooting to windows

<blockquote data-quote="Rhys.Goodwin" data-source="post: 134191" data-attributes="member: 27017">ok I see I was meant to put the ID at the end. Like this:[CODE] #dvbtune -f 1183000 -p h -tone 0 -s 22500 &amp;&amp; ./rb-download -v -b /home/rhys/tvnzmheg -f channels.conf 1035Using DVB card &quot;ST STV0299 DVB-S&quot;tuning DVB-S to L-Band:0, Pol:H Srate=22500000, 22kHz=offpolling....Getting frontend eventFE_STATUS:polling....Getting frontend eventFE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNCBit error rate: 3554Signal strength: 55668SNR: 59361FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNCTrying to open channels.confTODO: Only able to tune DVB-T devices at presentUnable to retune; let's hope you're already tuned to the right frequency...Unable to find Carousel Descriptor in PMT[/CODE]&quot;Unable to find Carousel Descriptor in PMT&quot;Any ideas what might casue this?Cheers,Rhys...Rebooting to windows</blockquote>

[QUOTE="Rhys.Goodwin, post: 134191, member: 27017"] ok I see I was meant to put the ID at the end. Like this: [CODE] #dvbtune -f 1183000 -p h -tone 0 -s 22500 && ./rb-download -v -b /home/rhys/tvnzmheg -f channels.conf 1035 Using DVB card "ST STV0299 DVB-S" tuning DVB-S to L-Band:0, Pol:H Srate=22500000, 22kHz=off polling.... Getting frontend event FE_STATUS: polling.... Getting frontend event FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC Bit error rate: 3554 Signal strength: 55668 SNR: 59361 FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC Trying to open channels.conf TODO: Only able to tune DVB-T devices at present Unable to retune; let's hope you're already tuned to the right frequency... Unable to find Carousel Descriptor in PMT [/CODE] "Unable to find Carousel Descriptor in PMT" Any ideas what might casue this? Cheers, Rhys ...Rebooting to windows [/QUOTE]