- October 13, 2007
- 6
- 0
- Home Country
-
Is it possible to access the line in (CVBS or S-Video) on a TV card.. is there a way.. will this ever be implemented ?.
thanks
thanks
Winfast PVR2000 and line in? howto? (1 Viewer)
- Thread starter Zaphod_Beebl
- Start date
If the video capture input is "software encoding" (and most are), then the answer is no .... 
However, if the video capture input is "hardware encoding", then it should already be supported. I don't know what type the Winfast PVR2000 is, but I strongly suspect that it is software encoding.
However, if the video capture input is "hardware encoding", then it should already be supported. I don't know what type the Winfast PVR2000 is, but I strongly suspect that it is software encoding.
- October 13, 2007
- 6
- 0
- Home Country
-
- Thread starter
- #3
Re: pvr2000 hardware or software card
The PVR2000 is a hardware card ... I find no way to access the line in within this software?
If the video capture input is "software encoding" (and most are), then the answer is no ....
However, if the video capture input is "hardware encoding", then it should already be supported. I don't know what type the Winfast PVR2000 is, but I strongly suspect that it is software encoding.
The PVR2000 is a hardware card ... I find no way to access the line in within this software?
- October 13, 2007
- 6
- 0
- Home Country
-
- Thread starter
- #5
Thank you
Thank you...
Much apeciated
now how do you get increments of 5 minutes for recording rather than 30.. IE I want to record 5 minutes before the start of a show then for an hour and ten minutes so I have a 5 minute buffer either side ... it seems this is not an option for record from line in
Thank you...
Much apeciated
now how do you get increments of 5 minutes for recording rather than 30.. IE I want to record 5 minutes before the start of a show then for an hour and ten minutes so I have a 5 minute buffer either side ... it seems this is not an option for record from line in
Users who are viewing this thread
Similar threads
OK....perhaps impatient of me I know, but went for a full reinstall....and now up and running once more.
Have no idea what was at the root of this problem....still wondering if it may've been due to a Win11 update earlier this week?
OK....perhaps impatient of me I know, but went for a full reinstall....and now up and running once more.
Have no idea what was at...
Have used MP1.38 64 successfully since it's introduction.....now something has changed.
Video folders are still present.....but now...
4.5 is really old. I'm not sure 4.5.5 even is a version that actually existed. You should be able to install .NET Framework 4.8.0 on Windows 7 SP1
4.5 is really old. I'm not sure 4.5.5 even is a version that actually existed. You should be able to install .NET Framework 4.8.0...
My TV PC is more a cast-off on older hardware (a 'Quiet PC' i5 4690, 16GB ram, 2xSSD 1xHDD, system graphics), mainly as a cheap way...
I haven't tested it.
I use MP1, but sometimes I try to help with MP2 :).
I haven't tested it.
I use MP1, but sometimes I try to help with MP2 :).
This happened immediately after my Windows 11 x64 monthly update for November. The update included also cumulative update to .NET...
I installed the new EXE on my MP 1.36 64-bit system (Win 10 laptop), and... it works fine. (y) :)
Thank you for making this change :). I hope that it will be included in the next release.
-- from CyberSimian in the UK
I installed the new EXE on my MP 1.36 64-bit system (Win 10 laptop), and... it works fine. (y) :)
Thank you for making this...
In "MP Config" the following setting enables the display of channel numbers in the TV EPG:
But there is no equivalent setting in...
Well, all that remains is to find someone who will add this render if it is a render.
Well, all that remains is to find someone who will add this render if it is a render.
Are there plans to support other video renderers?
MadVR got added a while ago, but this a 'hardcoded' selection in the...
