Reply to thread

Message

<blockquote data-quote="CyberSimian" data-source="post: 1282203" data-attributes="member: 141969">I just tried to reproduce this (on MP 1.25), but the behaviour described did not occur. Are you sure that you closed &quot;MP Config&quot; correctly?If you click &quot;Cancel&quot; or click the red &quot;X&quot; in the top right corner, simple changes that you made are discarded. So if you deselected &quot;Enable HID&quot; and then clicked the red &quot;X&quot;, when you next restarted &quot;MP Config&quot; you would find that &quot;Enable HID&quot; was still selected. <img src="data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7" class="smilie smilie--sprite smilie--sprite12" alt="o_O" title="Er... what?&nbsp; &nbsp; o_O" loading="lazy" data-shortname="o_O" />Because I use the Ortek/Hama remote control (which uses settings on the &quot;Sceneo&quot; tab), I have never looked in detail at the settings offered by the &quot;HID&quot; tab. I notice that &quot;ChannelUp&quot; and &quot;ChannelDown&quot; are the only two buttons that are flagged with &quot;(repeat)&quot; in the default &quot;Classic&quot; config. However...If you click &quot;Up&quot;, &quot;Down&quot;, &quot;Left&quot;, or &quot;Right&quot; (in the third section), you will see that they too are marked as &quot;Repeat&quot;, but &quot;(repeat)&quot; is not shown in the list on the left. Very strange (and inconsistent). <img src="data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7" class="smilie smilie--sprite smilie--sprite5" alt=":confused:" title="Confused&nbsp; &nbsp; :confused:" loading="lazy" data-shortname=":confused:" />Be that as it may, the default config has repeat enabled for the two channel buttons, so I suspect that that is how most people use it (and without encountering your problem). So it seems likely that there is still something weird about your particular setup. <img src="data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7" class="smilie smilie--sprite smilie--sprite9" alt=":eek:" title="Eek!&nbsp; &nbsp; :eek:" loading="lazy" data-shortname=":eek:" /> <img src="data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7" class="smilie smilie--sprite smilie--sprite16" alt=":cry:" title="Crying&nbsp; &nbsp; :cry:" loading="lazy" data-shortname=":cry:" />-- from CyberSimian in the UK</blockquote>

[QUOTE="CyberSimian, post: 1282203, member: 141969"] I just tried to reproduce this (on MP 1.25), but the behaviour described did not occur. Are you sure that you closed "MP Config" correctly? If you click "Cancel" or click the red "X" in the top right corner, simple changes that you made are discarded. So if you deselected "Enable HID" and then clicked the red "X", when you next restarted "MP Config" you would find that "Enable HID" was still selected. o_O Because I use the Ortek/Hama remote control (which uses settings on the "Sceneo" tab), I have never looked in detail at the settings offered by the "HID" tab. I notice that "ChannelUp" and "ChannelDown" are the only two buttons that are flagged with "(repeat)" in the default "Classic" config. However... If you click "Up", "Down", "Left", or "Right" (in the third section), you will see that they too are marked as "Repeat", but "(repeat)" is [i]not[/i] shown in the list on the left. Very strange (and inconsistent). :confused: Be that as it may, the default config has repeat enabled for the two channel buttons, so I suspect that that is how most people use it (and without encountering your problem). So it seems likely that there is still something weird about your particular setup. :eek: :cry: -- from CyberSimian in the UK [/QUOTE]

Verification