home
products
contribute
download
documentation
forum
Home
Forums
New posts
Search forums
What's new
New posts
All posts
Latest activity
Members
Registered members
Current visitors
Donate
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Forums
MediaPortal 1
Support
General Support
DiseqC problems after upgrade to 1.25
Contact us
RSS
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="AlunS" data-source="post: 1274465" data-attributes="member: 116408"><p>I recently upgraded my somewhat ancient 1.16 installation to the latest version, 1.25, and have a couple of problems, but the most serious one at the moment is that I no longer seem to be able to use DiseqC commands to switch from Astra 28.2E to Astra 19.2E.</p><p></p><p>I have two LNB's, a twin LNB aimed at Astra 28.2E, and second single LNB aimed at Astra 19.2E. One of the outputs of the twin LNB goes to tuner 1 on my satellite card, and there's a 2/1 DiseqC switch connecting the other output and the single LNB to tuner 2.</p><p></p><p>The satellite card is a Digital Devices Cine S2/V7A, the DiseqC switch is an Opticum DSG 2/1 OUT (claims to be DiseqC 2.0 compatible).</p><p></p><p>I have attached logs from an attempt to tune a channel on Astra 19.2E from SetupTv.exe, which very quickly returns an error "No signal found". </p><p></p><p>Performing a channel scan on tuner 2 (with only Astra 19.2E enabled) just results in a duplication of some of the channels on Astra 28.2 as there's an overlap in the transponder frequencies, which suggests that the DiseqC command is not working for some reason.</p><p></p><p>What's odd though is that TransEdit works perfectly, and I can do a full scan of Astra 19.2E, as does a demo version of DVB Viewer Pro.</p><p></p><p>Just to eliminate any problems with the upgrade, I installed MP 2 in parallel, but had exactly the same problem.</p><p></p><p>Running Windows 10 build 1909, and latest Digital Devices drivers.</p><p></p><p>Any ideas?</p></blockquote><p></p>
[QUOTE="AlunS, post: 1274465, member: 116408"] I recently upgraded my somewhat ancient 1.16 installation to the latest version, 1.25, and have a couple of problems, but the most serious one at the moment is that I no longer seem to be able to use DiseqC commands to switch from Astra 28.2E to Astra 19.2E. I have two LNB's, a twin LNB aimed at Astra 28.2E, and second single LNB aimed at Astra 19.2E. One of the outputs of the twin LNB goes to tuner 1 on my satellite card, and there's a 2/1 DiseqC switch connecting the other output and the single LNB to tuner 2. The satellite card is a Digital Devices Cine S2/V7A, the DiseqC switch is an Opticum DSG 2/1 OUT (claims to be DiseqC 2.0 compatible). I have attached logs from an attempt to tune a channel on Astra 19.2E from SetupTv.exe, which very quickly returns an error "No signal found". Performing a channel scan on tuner 2 (with only Astra 19.2E enabled) just results in a duplication of some of the channels on Astra 28.2 as there's an overlap in the transponder frequencies, which suggests that the DiseqC command is not working for some reason. What's odd though is that TransEdit works perfectly, and I can do a full scan of Astra 19.2E, as does a demo version of DVB Viewer Pro. Just to eliminate any problems with the upgrade, I installed MP 2 in parallel, but had exactly the same problem. Running Windows 10 build 1909, and latest Digital Devices drivers. Any ideas? [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
MediaPortal 1
Support
General Support
DiseqC problems after upgrade to 1.25
Contact us
RSS
Top
Bottom