Reply to thread

Message

<blockquote data-quote="1gkar" data-source="post: 786665" data-attributes="member: 53076">Only just seen this when searching for something else. As I use upscaling, try the following:Firstly, what codec(s) are you using? If SAF*.00, I would recommend upgrading to the latest 6.00, as upscaling is basically set. If not, then use my exported registry settings to see if they work. Remember, backup the registry or set system restore point before importing.Remove your ffdshow post-processing from MP config: I don't use this. The following are basically what I have set in the attached settings. Set your resize, sharpen, etc. filters on the default profile. Set up a new default profile, unchecking filters, to start with. Rename eg. SD Upscale. Open Preset Atuoload Conditions. Radio button 'on all conditions match'&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; Check 'on movie dimensions match'&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; 16 &lt;=width&lt;= 1279&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; 16 &lt;=height&lt;= 719&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; SaveSave another new profile. Rename to HD Upscale.Open Preset Atuoload Conditions. Radio button 'on all conditions match'&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; Check 'on movie dimensions match'&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; 1280 &lt;=width&lt;= 2048&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; 720 &lt;=height&lt;= 2048&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; SaveTo test, check OSD. Check:CPU LoadSource FileInput size &amp; aspect ratioOutput SizeRun MP in windowed mode, so you don't have to continually close out. Check if upscaling is working via OSD when running various files. When you have this working correctly, you could remove filters from default profile, &amp; set them, to the preferred settings, inside the profiles. Depending on what codecs your media files have been coded with, you could also use 'on fourCC match'Try this for a start.</blockquote>

[QUOTE="1gkar, post: 786665, member: 53076"] Only just seen this when searching for something else. As I use upscaling, try the following: Firstly, what codec(s) are you using? If SAF*.00, I would recommend upgrading to the latest 6.00, as upscaling is basically set. If not, then use my exported registry settings to see if they work. Remember, backup the registry or set system restore point before importing. Remove your ffdshow post-processing from MP config: I don't use this. The following are basically what I have set in the attached settings. Set your resize, sharpen, etc. filters on the default profile. Set up a new default profile, unchecking filters, to start with. Rename eg. SD Upscale. Open Preset Atuoload Conditions. Radio button 'on all conditions match' Check 'on movie dimensions match' 16 <=width<= 1279 16 <=height<= 719 Save Save another new profile. Rename to HD Upscale. Open Preset Atuoload Conditions. Radio button 'on all conditions match' Check 'on movie dimensions match' 1280 <=width<= 2048 720 <=height<= 2048 Save To test, check OSD. Check: CPU Load Source File Input size & aspect ratio Output Size Run MP in windowed mode, so you don't have to continually close out. Check if upscaling is working via OSD when running various files. When you have this working correctly, you could remove filters from default profile, & set them, to the preferred settings, inside the profiles. Depending on what codecs your media files have been coded with, you could also use 'on fourCC match' Try this for a start. [/QUOTE]

Verification