home
products
contribute
download
documentation
forum
Home
Forums
New posts
Search forums
What's new
New posts
All posts
Latest activity
Members
Registered members
Current visitors
Donate
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Forums
MediaPortal 1
MediaPortal 1 Talk
Hauppauge HD-PVR & Colossus Support
Contact us
RSS
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="motor" data-source="post: 752552" data-attributes="member: 88371"><p>1st Are you lucky enough to find your STB in the list of devices within blaster config (I wasn't but choose something like it)?</p><p></p><p>2nd Choose Advanced </p><p></p><p>3rd Choose Learning</p><p></p><p>Check the bullet is set to learn (not send)</p><p></p><p>Use your STB remote to learn the individual digits (point STB remote at the Colossus IR receiver (hold within a few cm or 1- 2 inches) and push the corresponding key several times quickly - should come up with succes or fail, repeat until you have learned all digits +/- on</p><p></p><p>Position the blaster bud over the STB IR sensor, if you can't see it keep sending the power on command and move the bud around until the STB responds - stick in place.</p><p></p><p>Not absolutely required but to check I used Wintv7 windowed, chose to use it to control STB (settings,devices, tuner) video input via component.</p><p></p><p>Blast a few numbers via the blaster config (change the bullet from learn to send or use the little input box) Test all the digits eg send 123 456 789 000 you should see them in the OSD in the Wintv app</p><p></p><p>If all working enter MP tv server config</p><p></p><p>tv channels - add or if the channel is already setup edit and edit again enter the corresponding STB channel number, freq = 0, input, cable, country, us, vcr input leave unchecked, vid source, YRYBY #1, aud source, (i use stereo via line in#1 - for optical use spdif#2 - I believe) - will be the same as what you already have if you can see STB in MP. The channel number is what is important as that is what is blasted ok etc</p><p></p><p>Also make sure the analog channels (STB) are mapped to the hauppage colossus crossbar 0</p><p></p><p>In tvserver goto plugins tick serverblaster</p><p>choose + and enter serverblaster config - blaster type - Hauppuage ok</p><p></p><p>Hopefully that is enough to get you going</p></blockquote><p></p>
[QUOTE="motor, post: 752552, member: 88371"] 1st Are you lucky enough to find your STB in the list of devices within blaster config (I wasn't but choose something like it)? 2nd Choose Advanced 3rd Choose Learning Check the bullet is set to learn (not send) Use your STB remote to learn the individual digits (point STB remote at the Colossus IR receiver (hold within a few cm or 1- 2 inches) and push the corresponding key several times quickly - should come up with succes or fail, repeat until you have learned all digits +/- on Position the blaster bud over the STB IR sensor, if you can't see it keep sending the power on command and move the bud around until the STB responds - stick in place. Not absolutely required but to check I used Wintv7 windowed, chose to use it to control STB (settings,devices, tuner) video input via component. Blast a few numbers via the blaster config (change the bullet from learn to send or use the little input box) Test all the digits eg send 123 456 789 000 you should see them in the OSD in the Wintv app If all working enter MP tv server config tv channels - add or if the channel is already setup edit and edit again enter the corresponding STB channel number, freq = 0, input, cable, country, us, vcr input leave unchecked, vid source, YRYBY #1, aud source, (i use stereo via line in#1 - for optical use spdif#2 - I believe) - will be the same as what you already have if you can see STB in MP. The channel number is what is important as that is what is blasted ok etc Also make sure the analog channels (STB) are mapped to the hauppage colossus crossbar 0 In tvserver goto plugins tick serverblaster choose + and enter serverblaster config - blaster type - Hauppuage ok Hopefully that is enough to get you going [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
MediaPortal 1
MediaPortal 1 Talk
Hauppauge HD-PVR & Colossus Support
Contact us
RSS
Top
Bottom
