Reply to thread

Message

Yeah, the Rumblepad 2 is a great little pad, I'm really glad I decided to spend the extra 10 bucks and spring for it!

But I'm still having trouble with the 'end process' combination. I uninstalled MP and wiped the remaining folders to get a clean install on 0.2.2.0.

I set the end process combo in the "Direct Input" section of the Remotes dialogue in setup.exe. I use the four front triggers simultaneously to end process - I think it maps as 02,03,04,05 but I might be off on that. It works fine for a while, but eventually quits responding. When I go back to the "Direct Input" dialogure, the end process field is blank and I have to teach it the combo again. Then the cycle begins anew.

I haven't been able to isolate what's causing this, but I have been messing with the configuration a lot lately trying to get 0.2.2.0 set up like I had 2.1. Once in a while, when setup.exe is started I get the "MP is not shutdown" dialogue even though I asked it to shutdown. I always click the "ok, shut it down and continue" button and the end process combo is always dead after this.

Aside from avoiding the "MP is not shutdown" dialogue, any thoughts on how to retain my end process combination?

Thanks in advance.

<blockquote data-quote="dcwp" data-source="post: 101588" data-attributes="member: 25562">Yeah, the Rumblepad 2 is a great little pad, I'm really glad I decided to spend the extra 10 bucks and spring for it!But I'm still having trouble with the 'end process' combination.&nbsp; I uninstalled MP and wiped the remaining folders to get a clean install on 0.2.2.0.&nbsp; I set the end process combo in the &quot;Direct Input&quot; section of the Remotes dialogue in setup.exe.&nbsp; I use the four front triggers simultaneously to end process - I think it maps as 02,03,04,05 but I might be off on that.&nbsp; It works fine for a while, but eventually quits responding.&nbsp; When I go back to the &quot;Direct Input&quot; dialogure, the end process field is blank and I have to teach it the combo again.&nbsp; Then the cycle begins anew.&nbsp; I haven't been able to isolate what's causing this, but I have been messing with the configuration a lot lately trying to get 0.2.2.0 set up like I had 2.1.&nbsp; Once in a while, when setup.exe is started I get the &quot;MP is not shutdown&quot; dialogue even though I asked it to shutdown.&nbsp; I always click the &quot;ok, shut it down and continue&quot; button and the end process combo is always dead after this.&nbsp; Aside from avoiding the &quot;MP is not shutdown&quot; dialogue, any thoughts on how to retain my end process combination?Thanks in advance.</blockquote>

[QUOTE="dcwp, post: 101588, member: 25562"] Yeah, the Rumblepad 2 is a great little pad, I'm really glad I decided to spend the extra 10 bucks and spring for it! But I'm still having trouble with the 'end process' combination. I uninstalled MP and wiped the remaining folders to get a clean install on 0.2.2.0. I set the end process combo in the "Direct Input" section of the Remotes dialogue in setup.exe. I use the four front triggers simultaneously to end process - I think it maps as 02,03,04,05 but I might be off on that. It works fine for a while, but eventually quits responding. When I go back to the "Direct Input" dialogure, the end process field is blank and I have to teach it the combo again. Then the cycle begins anew. I haven't been able to isolate what's causing this, but I have been messing with the configuration a lot lately trying to get 0.2.2.0 set up like I had 2.1. Once in a while, when setup.exe is started I get the "MP is not shutdown" dialogue even though I asked it to shutdown. I always click the "ok, shut it down and continue" button and the end process combo is always dead after this. Aside from avoiding the "MP is not shutdown" dialogue, any thoughts on how to retain my end process combination? Thanks in advance. [/QUOTE]