Reply to thread

Message

<blockquote data-quote="Django.edwards" data-source="post: 773354" data-attributes="member: 98942">Hi mm,sorry for my late reply, but I was really busy.Finally I found the time to do some more test. 1. scanning engine not working reliable:What I have done is the following: I removed the CI module on card 1 and did these test only with card 1.My test scenario was the following: - I switch the computer off and checked the cabling and the dish with my smartmeter S10, everything was fine and I had a good signal quality. So I start with switching the computer on.Then I did a fullscan on the first card, on the Hotbird LNB the scan found nothing on 17 transponders and for the Astra LNB he found nothing for 21 transponders. See log &quot;fullscan 1st card without cam.rar&quot;.- Then I closed the server config and restarted the TV serviceThen I did a second run to be shure that the results are occurate. Here I found nothing for 37 tp on Hotbird and nothing for 28 tp on Astra. See logfile:&quot;fullscan 1st card without cam 2nd try.rar&quot;- Then I removed the tick &quot;enable cam&quot; on the first card and restarted the TV service again.On this run the result was even worst, on Hotbird he found nothing for about 45 tp and on Astra the scan found no working tp at all. see log: &quot;fullscan 1st card without cam without cam marked 3rd try.rar&quot;-Then I put DVB-S as provider into the config of the first card and put the tick into the &quot;cam enabled&quot; and restarted the TV serviceOn this run, the scan found nothing at all. See log: &quot;fullscan 1st card without cam with dvbs marked 4th try.rar&quot;-After this, I leaved the config as it was and I did a reset of the computer and restarted the fullscan.Now, the fullscan found each transponder and everything was fine: see log:&quot;fullscan 4th try after reset.rar&quot;-To bee shure I did another scan with the same setting after a restart of the tv service. See log:&quot;fullscan 1st card without cam with dvbs mark 2nd try.rar&quot;. Everything fine.-Then I switched the provider back to &quot;generic&quot; and did another test... here I didn't find several tp. sorry no log for this.So, finally I put my both cards on provider &quot;DVB-S&quot;, with cam enabled for both. The first card without cam inserted, the second card with cam inserted.On this run both card worked fine, they found every transponder.So this seems to be my working scenario.Can you explain me what the technical background for the different provider settings is? Only to understand what this setting does.I hope that these test where helpfull for you to see something valuable. If you need some more investigations from my side, please let me know.Thanks in advanceDjango</blockquote>

[QUOTE="Django.edwards, post: 773354, member: 98942"] Hi mm, sorry for my late reply, but I was really busy. Finally I found the time to do some more test. 1. scanning engine not working reliable: What I have done is the following: I removed the CI module on card 1 and did these test only with card 1.My test scenario was the following: - I switch the computer off and checked the cabling and the dish with my smartmeter S10, everything was fine and I had a good signal quality. So I start with switching the computer on. Then I did a fullscan on the first card, on the Hotbird LNB the scan found nothing on 17 transponders and for the Astra LNB he found nothing for 21 transponders. See log "fullscan 1st card without cam.rar". - Then I closed the server config and restarted the TV service Then I did a second run to be shure that the results are occurate. Here I found nothing for 37 tp on Hotbird and nothing for 28 tp on Astra. See logfile:"fullscan 1st card without cam 2nd try.rar" - Then I removed the tick "enable cam" on the first card and restarted the TV service again. On this run the result was even worst, on Hotbird he found nothing for about 45 tp and on Astra the scan found no working tp at all. see log: "fullscan 1st card without cam without cam marked 3rd try.rar" -Then I put DVB-S as provider into the config of the first card and put the tick into the "cam enabled" and restarted the TV service On this run, the scan found nothing at all. See log: "fullscan 1st card without cam with dvbs marked 4th try.rar" -After this, I leaved the config as it was and I did a reset of the computer and restarted the fullscan. Now, the fullscan found each transponder and everything was fine: see log:"fullscan 4th try after reset.rar" -To bee shure I did another scan with the same setting after a restart of the tv service. See log:"fullscan 1st card without cam with dvbs mark 2nd try.rar". Everything fine. -Then I switched the provider back to "generic" and did another test... here I didn't find several tp. sorry no log for this. So, finally I put my both cards on provider "DVB-S", with cam enabled for both. The first card without cam inserted, the second card with cam inserted. On this run both card worked fine, they found every transponder. So this seems to be my working scenario. Can you explain me what the technical background for the different provider settings is? Only to understand what this setting does. I hope that these test where helpfull for you to see something valuable. If you need some more investigations from my side, please let me know. Thanks in advance Django [/QUOTE]

Verification