Reply to thread

Message

<blockquote data-quote="Dr Morris" data-source="post: 1233280" data-attributes="member: 131048">Hi all,I've always had occasional difficulties with MEPO presenting me with a &quot;stopped working&quot; whenever I turn on the TV and AVR.&nbsp; Everything is fine when the TV turns off and this in turn uses HDMI to turn off the AVR.&nbsp; When turning things on, the AVR is turned on and then the TV using a Harmony Hub to orchestrate things. I've tried ordering things differently but this makes no difference.The issue has been pretty bad since v18 :-(&nbsp; though and I'm hoping the community can assist.&nbsp; I see plenty of historical posts on this topic so guess its a perennial problem, but I need to put some stability in place.&nbsp; I am running a minimal set of plug ins and have with previous versions completely re-installed from scratch to narrow things down.Logs attached.&nbsp; in the attached:<ul>
<li data-xf-list-type="ul">MEPO Started</li>
<li data-xf-list-type="ul">BBC One HD started</li>
<li data-xf-list-type="ul">TV/AVR switched off</li>
<li data-xf-list-type="ul">Wait 10 seconds</li>
<li data-xf-list-type="ul">TV/AVR switched on</li>
<li data-xf-list-type="ul">Full picture exists, but blocky and stutters - recover</li>
<li data-xf-list-type="ul">TV/AVR switched off</li>
<li data-xf-list-type="ul">Wait 10 seconds</li>
<li data-xf-list-type="ul">TV/AVR Switched on</li>
<li data-xf-list-type="ul">MEPO crashed message</li>
<li data-xf-list-type="ul">Logs collected and attached</li>
</ul>I'm running:W10 1703 build 15063.674 Defender (all mepo directories excluded and I've tried running with it off)Samsung TV and Denon AVR X3000. Grateful for any thoughts, hints, tips or magic dust available.FYI that the AVR is set so that the passthru feed is the PCTV as previously when turning everything on the sound would hit the TV first because the TV won't detect the AVR until its powered up and the AVR kicks in - i thin all of this may be interlinked but I've not found a combo that stops the crash.</blockquote>

[QUOTE="Dr Morris, post: 1233280, member: 131048"] Hi all, I've always had occasional difficulties with MEPO presenting me with a "stopped working" whenever I turn on the TV and AVR. Everything is fine when the TV turns off and this in turn uses HDMI to turn off the AVR. When turning things on, the AVR is turned on and then the TV using a Harmony Hub to orchestrate things. I've tried ordering things differently but this makes no difference. The issue has been pretty bad since v18 :-( though and I'm hoping the community can assist. I see plenty of historical posts on this topic so guess its a perennial problem, but I need to put some stability in place. I am running a minimal set of plug ins and have with previous versions completely re-installed from scratch to narrow things down. Logs attached. in the attached: [LIST] [*]MEPO Started [*]BBC One HD started [*]TV/AVR switched off [*]Wait 10 seconds [*]TV/AVR switched on [*]Full picture exists, but blocky and stutters - recover [*]TV/AVR switched off [*]Wait 10 seconds [*]TV/AVR Switched on [*]MEPO crashed message [*]Logs collected and attached [/LIST] I'm running: [B]W10 1703 build 15063.674 Defender (all mepo directories excluded and I've tried running with it off) Samsung TV and Denon AVR X3000.[/B] Grateful for any thoughts, hints, tips or magic dust available. [SIZE=2]FYI that the AVR is set so that the passthru feed is the PCTV as previously when turning everything on the sound would hit the TV first because the TV won't detect the AVR until its powered up and the AVR kicks in - i thin all of this may be interlinked but I've not found a combo that stops the crash.[/SIZE] [/QUOTE]

Verification