home
products
contribute
download
documentation
forum
Home
Forums
New posts
Search forums
What's new
New posts
All posts
Latest activity
Members
Registered members
Current visitors
Donate
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Forums
MediaPortal 1
MediaPortal 1 Talk
Multiple Hauppauge Colossus cards -- pre- and post-recording behavior?
Contact us
RSS
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Karyudo" data-source="post: 1036545" data-attributes="member: 65921"><p>I installed MP 1.50 today and did some testing. Windows 7 32-bit, 2x Hauppauge Colossus, 1x ATSC tuner, 2x Motorola 6200 STBs. Some results:</p><p></p><p>1. I couldn't figure out how to install only the TVServer portion and still be able to load plugins (e.g. for EPG via SchedulesDirect), so I had to go back and reinstall with a full "single seat" installation.</p><p>2. MP found the ATSC card and Colossus crossbars right away. So I got video from all sources pretty much immediately. That was a pleasant surprise.</p><p>3. I can't figure out how to set audio input properly. Yet.</p><p>4. I can't figure out how to get SageChanger.exe (upgrade to the timmoore STB FireWire "channel.exe") to do the channel changing. Yet.</p><p>5. Ran a test, setting recordings for two back-to-back shows with pre- and post-roll from a single channel, available on both Colossus cards: success! Both shows seem to have come from the same STB, and both are correctly padded.</p><p></p><p>I'm going to have at least one more hurdle, I think, and that is to find out whether MP re-sends the channel change between two back-to-back shows on the same channel. I sure hope not. Because if it does, then the OSD of the STB will appear and be recorded!</p></blockquote><p></p>
[QUOTE="Karyudo, post: 1036545, member: 65921"] I installed MP 1.50 today and did some testing. Windows 7 32-bit, 2x Hauppauge Colossus, 1x ATSC tuner, 2x Motorola 6200 STBs. Some results: 1. I couldn't figure out how to install only the TVServer portion and still be able to load plugins (e.g. for EPG via SchedulesDirect), so I had to go back and reinstall with a full "single seat" installation. 2. MP found the ATSC card and Colossus crossbars right away. So I got video from all sources pretty much immediately. That was a pleasant surprise. 3. I can't figure out how to set audio input properly. Yet. 4. I can't figure out how to get SageChanger.exe (upgrade to the timmoore STB FireWire "channel.exe") to do the channel changing. Yet. 5. Ran a test, setting recordings for two back-to-back shows with pre- and post-roll from a single channel, available on both Colossus cards: success! Both shows seem to have come from the same STB, and both are correctly padded. I'm going to have at least one more hurdle, I think, and that is to find out whether MP re-sends the channel change between two back-to-back shows on the same channel. I sure hope not. Because if it does, then the OSD of the STB will appear and be recorded! [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
MediaPortal 1
MediaPortal 1 Talk
Multiple Hauppauge Colossus cards -- pre- and post-recording behavior?
Contact us
RSS
Top
Bottom