Reply to thread

Message

<blockquote data-quote="MaKin" data-source="post: 1002328" data-attributes="member: 141943">Ok guys, Im finally setting up MePo right now. A few questions:&nbsp;<ol>
<li data-xf-list-type="ol">Refresh Rate Settings, Im not quite sure what you meant by &quot;Enable dynamic refresh rate plugin 
23.976/24fps = 24 hz, 29.X/30/59.X/60fps = 60hz, 25/50fps = 50hz&quot;</li>
<li data-xf-list-type="ol">In <a href="http://wiki.team-mediaportal.com/1_MEDIAPORTAL_1/141_Configuration/MediaPortal_Configuration/9_Codecs_and_Renderer/3_MP_Audio_Renderer_(MPAR)/Configuration" target="_blank">t</a>he MPAR-Config-Guide you posted you can read &quot;When you use the LAV Audio Decoder in combination with the MediaPortal Audio Renderer, make sure you keep ALL bitstreaming Formats and the Auto A/V Sync correction option UNchecked (because these settings break the functionality of the MediaPortal Audio Renderer).&quot; &lt;-- When I do so, then the audio will be sent as PCM to the AVR. If I enable it, then the audio is transmitted properly as DTS, DTS-HD and so on. Will I gain any quality that way? In your guide you also mentioned to uncheck those boxes. But like I said, my AVR receives a PCM signal then...</li>
<li data-xf-list-type="ol">In MPAR - what's the difference between &quot;5.1&quot; and &quot;5.1 Surround&quot;?</li>
<li data-xf-list-type="ol">I installed AnyDVD HD and the BluRays just play fine, do I have to configure anything?</li>
<li data-xf-list-type="ol">Is it possible to start PowerDVD when playing a BluRay and going back to MediaPortal when the playback is stopped?</li>
<li data-xf-list-type="ol">My remote works with some buttons like numbers, arrows etc. but the essentials ones do not work like play, pause, skip, stop, etc.</li>
<li data-xf-list-type="ol">I can power the computer off with the remote but not start it afterwards. Common problem</li>
<li data-xf-list-type="ol">Unfortunately I still suffer from 24p stuttering. I have to mention though that I only enabled the &quot;Dynamic Refresh Rate&quot; without changing anything.</li>
</ol>Thanks again for your support!</blockquote>

[QUOTE="MaKin, post: 1002328, member: 141943"] Ok guys, Im finally setting up MePo right now. A few questions: [LIST=1] [*]Refresh Rate Settings, Im not quite sure what you meant by "Enable dynamic refresh rate plugin 23.976/24fps = 24 hz, 29.X/30/59.X/60fps = 60hz, 25/50fps = 50hz" [*]In [URL='http://wiki.team-mediaportal.com/1_MEDIAPORTAL_1/141_Configuration/MediaPortal_Configuration/9_Codecs_and_Renderer/3_MP_Audio_Renderer_(MPAR)/Configuration']t[/URL]he MPAR-Config-Guide you posted you can read "When you use the LAV Audio Decoder in combination with the MediaPortal Audio Renderer, make sure you keep ALL bitstreaming Formats and the Auto A/V Sync correction option UNchecked (because these settings break the functionality of the MediaPortal Audio Renderer)." <-- When I do so, then the audio will be sent as PCM to the AVR. If I enable it, then the audio is transmitted properly as DTS, DTS-HD and so on. Will I gain any quality that way? In your guide you also mentioned to uncheck those boxes. But like I said, my AVR receives a PCM signal then... [*]In MPAR - what's the difference between "5.1" and "5.1 Surround"? [*]I installed AnyDVD HD and the BluRays just play fine, do I have to configure anything? [*]Is it possible to start PowerDVD when playing a BluRay and going back to MediaPortal when the playback is stopped? [*]My remote works with some buttons like numbers, arrows etc. but the essentials ones do not work like play, pause, skip, stop, etc. [*]I can power the computer off with the remote but not start it afterwards. Common problem [*]Unfortunately I still suffer from 24p stuttering. I have to mention though that I only enabled the "Dynamic Refresh Rate" without changing anything. [/LIST] Thanks again for your support! [/QUOTE]

Verification