Reply to thread

Message

<blockquote data-quote="Sigpi007" data-source="post: 1118902" data-attributes="member: 133193">And... I spoke too fast.&nbsp;&nbsp; But... in all fairness, this may be a separate issue... though its much more severe now than it was before.When watching TV today, I had one show recording which I was watching LIVE while it was recording (channel 203).&nbsp;&nbsp; Then I tried to change to a separate channel to watch something different (220).&nbsp;&nbsp; When I did that, it crashed the TV server (&quot;unknown error occured&quot;) and essentially froze the MP client.&nbsp;&nbsp; I closed the client, confirmed that the TV server had stopped... started it up again and dumped the logs.&nbsp;&nbsp; Will attach below.THEN... since I had restarted TV server... I entered the MP client again and selected the channel I had wanted to watch (220).&nbsp;&nbsp; Still could not do it.&nbsp; Error returned was &quot;unknown error occured.&quot;&nbsp;&nbsp; TV server crashed again.THEN... I restarted the TV server again.&nbsp; However... this time I chose any channel other that 203 and 220.&nbsp;&nbsp; This time I got &quot;could not create graph&quot; errors for channel 219, and other channels.&nbsp;&nbsp; etc.&nbsp;&nbsp; However, differnce this time was that those errors did not kill the TV server..&nbsp;&nbsp; Then I dumped those log files and exited the client.&nbsp; I also opened the TV Server config and saw that all tuners were showing up in the config as expected. FINALLY... I analyzed the current state of the Ceton InfiniTV Eth 6 tuner through its admin interface... and I noticed that tuner #1 and tuner # 5 were listed as &quot;PLAYING&quot;.&nbsp; Tuners 2, 3, 4, and 6 were &quot;STOPPED&quot; which means nothing is playing.&nbsp;&nbsp; Tuner 1 was playing channel 203.&nbsp;&nbsp; Tuner 5 was playing 220.&nbsp; &nbsp; So to test a hypothesis... I manually set Tuner #1 status to &quot;STOPPED&quot; in the interface, and then I started the MP Client again.&nbsp;&nbsp; Can't remember if I cycled the TV Server.&nbsp;&nbsp; Anywho... this time I was able to watch channels again. Long story short... there are a couple things that seem not right.#1... Something initially caused the TV server to become unstable.&nbsp;&nbsp; Possibly related to watching a recording live and trying to switch away from it.#2... Even if those 2 tuners (numbers 1 and 5) were locked for use, the TV Server should have tuned using one of the 3 or 4 available tuners.&nbsp;&nbsp; [DOUBLEPOST=1420771017][/DOUBLEPOST]Here are the logs... the MPIPTV filters also had dump files around 300MB each.&nbsp; 2 files.&nbsp; I still have these and can share if needed.[DOUBLEPOST=1420771560][/DOUBLEPOST]And here's an excerpt from the Ceton Logs...</blockquote>

[QUOTE="Sigpi007, post: 1118902, member: 133193"] And... I spoke too fast. But... in all fairness, this may be a separate issue... though its much more severe now than it was before. When watching TV today, I had one show recording which I was watching LIVE while it was recording (channel 203). Then I tried to change to a separate channel to watch something different (220). When I did that, it crashed the TV server ("unknown error occured") and essentially froze the MP client. I closed the client, confirmed that the TV server had stopped... started it up again and dumped the logs. Will attach below. THEN... since I had restarted TV server... I entered the MP client again and selected the channel I had wanted to watch (220). Still could not do it. Error returned was "unknown error occured." TV server crashed again. THEN... I restarted the TV server again. However... this time I chose any channel other that 203 and 220. This time I got "could not create graph" errors for channel 219, and other channels. etc. However, differnce this time was that those errors did not kill the TV server.. Then I dumped those log files and exited the client. I also opened the TV Server config and saw that all tuners were showing up in the config as expected. FINALLY... I analyzed the current state of the Ceton InfiniTV Eth 6 tuner through its admin interface... and I noticed that tuner #1 and tuner # 5 were listed as "PLAYING". Tuners 2, 3, 4, and 6 were "STOPPED" which means nothing is playing. Tuner 1 was playing channel 203. Tuner 5 was playing 220. So to test a hypothesis... I manually set Tuner #1 status to "STOPPED" in the interface, and then I started the MP Client again. Can't remember if I cycled the TV Server. Anywho... this time I was able to watch channels again. [B]Long story short... there are a couple things that seem not right. #1... Something initially caused the TV server to become unstable. Possibly related to watching a recording live and trying to switch away from it. #2... Even if those 2 tuners (numbers 1 and 5) were locked for use, the TV Server should have tuned using one of the 3 or 4 available tuners. [/B][DOUBLEPOST=1420771017][/DOUBLEPOST]Here are the logs... the MPIPTV filters also had dump files around 300MB each. 2 files. I still have these and can share if needed.[DOUBLEPOST=1420771560][/DOUBLEPOST]And here's an excerpt from the Ceton Logs... [/QUOTE]

Verification