home
products
contribute
download
documentation
forum
Home
Forums
New posts
Search forums
What's new
New posts
All posts
Latest activity
Members
Registered members
Current visitors
Donate
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Forums
MediaPortal 1
Support
Watch / Listen Media
Television (MyTV frontend and TV-Server)
cannot see anything with 2 hvr4000
Contact us
RSS
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Mew" data-source="post: 230098" data-attributes="member: 29012"><p>Hi wladko</p><p></p><p>I am afraid I do not have any experience of using DiSEqC on multi LNBs. When I was using DVB-S with a Quad LNB set-up, it was a physical single LNB unit with one feedhorn but 4 outputs which could be controlled independently. I used two of these with one connected to each of my HVR-4000s. While I was tuned to 2 different satellites on each card they were very close together (at 28.5E and 28.8E) so TV Server only needed to use one LNB for each card to scan. </p><p></p><p>I think there are issues with the HVR-4000 as has been posted on the Hauppage forums (<a href="http://www.hauppauge.co.uk/board/showthread.php?t=14207" target="_blank">http://www.hauppauge.co.uk/board/showthread.php?t=14207</a>) by chemelli (who is also posts on these forums). Another thread is here <a href="http://www.hauppauge.co.uk/board/showthread.php?t=13647" target="_blank">http://www.hauppauge.co.uk/board/showthread.php?t=13647</a></p><p>This is possibly what is causing the problem, if I understand the posts correctly, as you say you are experiencing it in all software, not just MediaPortal.</p><p></p><p>I am still using v3.4b of the drivers. I didn't switch to v4.0 because it said they didn't support HD. That said, from what I understand, the older drivers didn't support DVB-S2 properly as there were parameters missing. This was mentioned on these forums and I don't know if it has been fixed. I am not sure if Hauppauge's not about the drivers being "Standard Definition only" is because they are Media Center of Vista drivers and Media Center and Vista do not support non-USA HD (only Vista supports USA HD).</p><p></p><p>I probably could switch to 4.0 (or 4.1 that seemed to change quickly from being the current driver to pre-release) as I am currently only using DVB-T and it is working fine for me. I have put up my new satellite dish but can not get any signal. It may be due to some trees that I did not think were in the line of sight of the satellite but may be. I may have to resort to calling in a professional installer when I get round to it.</p><p></p><p>I am sorry I couldn't be any more help.</p><p></p><p>Mew</p></blockquote><p></p>
[QUOTE="Mew, post: 230098, member: 29012"] Hi wladko I am afraid I do not have any experience of using DiSEqC on multi LNBs. When I was using DVB-S with a Quad LNB set-up, it was a physical single LNB unit with one feedhorn but 4 outputs which could be controlled independently. I used two of these with one connected to each of my HVR-4000s. While I was tuned to 2 different satellites on each card they were very close together (at 28.5E and 28.8E) so TV Server only needed to use one LNB for each card to scan. I think there are issues with the HVR-4000 as has been posted on the Hauppage forums ([URL="http://www.hauppauge.co.uk/board/showthread.php?t=14207"]http://www.hauppauge.co.uk/board/showthread.php?t=14207[/URL]) by chemelli (who is also posts on these forums). Another thread is here [URL="http://www.hauppauge.co.uk/board/showthread.php?t=13647"]http://www.hauppauge.co.uk/board/showthread.php?t=13647[/URL] This is possibly what is causing the problem, if I understand the posts correctly, as you say you are experiencing it in all software, not just MediaPortal. I am still using v3.4b of the drivers. I didn't switch to v4.0 because it said they didn't support HD. That said, from what I understand, the older drivers didn't support DVB-S2 properly as there were parameters missing. This was mentioned on these forums and I don't know if it has been fixed. I am not sure if Hauppauge's not about the drivers being "Standard Definition only" is because they are Media Center of Vista drivers and Media Center and Vista do not support non-USA HD (only Vista supports USA HD). I probably could switch to 4.0 (or 4.1 that seemed to change quickly from being the current driver to pre-release) as I am currently only using DVB-T and it is working fine for me. I have put up my new satellite dish but can not get any signal. It may be due to some trees that I did not think were in the line of sight of the satellite but may be. I may have to resort to calling in a professional installer when I get round to it. I am sorry I couldn't be any more help. Mew [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
MediaPortal 1
Support
Watch / Listen Media
Television (MyTV frontend and TV-Server)
cannot see anything with 2 hvr4000
Contact us
RSS
Top
Bottom
