DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC) (2 Viewers)

[morpheus_xx]

AW: DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC)

Thanks for testing!

Please ALWAYS add logs so that I can check what is (not)working!

 

[riksmith]

Please only speak english here, for people who can't there is a german forum.

 

[Darkroom]

AW: Re: DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC)

I installed the V2 yesterday and had a failure by starting the TVServer at end of the install.
But the server worked without problems. 1 problem i had with the previously version was when I want to record
2 following movies from the same channel - normally the server should both movies record with 5 minutes in front and the end of the movie
with V2 it´s o.k. with the prev. version he recorded the 1st movie o.k., but the 2nd movie stratet when the record of the 1st movie stops.
So it´s an important improvement for me

thanks to morpheus

 

[dirki1972]

AW: DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC)

after v2 descrambling stop working for me
before all work except cam menu.

and now if i enable cam, then the tv client cant connect to server, after disable cam tv working fine again.

i dont know how go back to your v1 because this works almost perfect for me.

all install new again


regards
dirk

PS: what is the different between hardware rev. v4 / v5 / v5.5 ?

 

[Darkroom]

AW: DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC)

The 1st update of V2 not worked it broke after the deletion of files cause he can´t stop the TVserver service
after i stopped it manually i run the V2 update again - get a failure message on starting the TVserver - but it works´s
Did you really look if the installation run complete???
the versions are hardware revision - in the latest rev. you can connect the CI or a 2nd Flextuner with the card without the PCI-E bridge, so you need only one PCI-E slot for 2 cards (4 Tuner or 2 Tuner & CI) - it´s nice if you run out of Slots ;-)
I didn´t test it - works only with the latest driver.

 

[dirki1972]

AW: DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC)

The 1st update of V2 not worked it broke after the deletion of files cause he can´t stop the TVserver service
after i stopped it manually i run the V2 update again - get a failure message on starting the TVserver - but it works´s
Did you really look if the installation run complete???
the versions are hardware revision - in the latest rev. you can connect the CI or a 2nd Flextuner with the card without the PCI-E bridge, so you need only one PCI-E slot for 2 cards (4 Tuner or 2 Tuner & CI) - it´s nice if you run out of Slots ;-)
I didn´t test it - works only with the latest driver.

yes the installation run complete without errors.

 

[dirki1972]

AW: DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC)

hi morpheus,
i am confused it work now again..... little stuttering sometimes in time descrambling but it works.

maybe you can see something in my log files i give you in last post.


regards
dirk

 

[lhcomputer]

AW: DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC)

hi morpheus_xx, thanks for your work


Here my first short Test Results . Sorry for my bad English.


Hardware:
Cine 2 with CI Connector V5 , CI Modul without Bridge
Alphy Crypt Light
driver v:.1.4.3.44 , Channel List from my Floppy DTV
Your V2 Software

First Test it work

Channel Scan Derypt to decrypt work (Channel Times OK)
3 decrypt Channel record (at the same TIme) an 1 decrypt Channel show - OK
Channel switch between free Channel OK
CI Menü work
Stand By to decrypt SD and decrypt HD Channel OK


After some times
Very Long Times between Channels Switch (decrypt and Free Channel)
Problems between free Channel. No Channel Switch , go back to the Channel before
Play the TImeshift Buffer from the last Channel.
Error Channel is decrypt; After tune the same Channel work.

This is only a Test for a very short time.
I´hope I have more time in the next Days to Test it more.

lh Computer - A.Herberg

 

[morpheus_xx]

AW: DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC)

dirki1972 & lhcomputer: I have no idea about your issues currently

but I have updated the 1st post with a new build (RC4_v3), which is IMHO the "final one". All (from coding part) known issues are now solved, code got cleaned up and detection has been improved.

 

[dyamant]

AW: DigitalDevices Dual DVB-S2 Testing (CAM/DiSEqC)

This release doesnt work with mdapi.

See log files.

I hope you can fix it that i can used the optimized filter for my DD Satcard.