firedtv remote wakeup (1 Viewer)

[snorredick]

TV-Server Version: 1.0 rc1 svn-05-16-2008--23-38-Rev19127
MediaPortal Version: 1.0 rc1 svn-05-16-2008--23-38-Rev19127
MediaPortal Skin: BlueTwo
Windows Version: xp sp3
CPU Type: AMD 5000+
HDD: Western Digital 250 GB
Memory: 3gb DDR2 pc5300
Motherboard: asus m2a-vm-hdmi
Video Card: ati radeon xpress 1250
Video Card Driver: 8.342
Sound Card: realtek intergrated
Sound Card AC3: no AC3
Sound Card Driver: 5.10.0.5434
1. TV Card: firedtv
1. TV Card Type: DVB-C
1. TV Card Driver: 4-5-n
2. TV Card:
2. TV Card Type:
2. TV Card Driver:
3. TV Card:
3. TV Card Type:
3. TV Card Driver:
4. TV Card:
4. TV Card Type:
4. TV Card Driver:
MPEG2 Video Codec:
MPEG2 Audio Codec:
h.264 Video Codec:
Satelite/CableTV Provider: comhem
HTPC Case: antec fusion
Cooling: scythe ninja mini
Power Supply: Antec NSK2480 380W
Remote: firedtv remote
TV: telefunken
TV - HTPC Connection: composite


Hi

Ive been playing around now with the remote mapping within the MP config for awhile to make the pc sleep/wakeup from the remote, the sleeppart were easily done but to wake it back up seems more of a problem, as from what ive read so far a USB device would need to be jumpered differently on the motherboard, but does this also apply to a firewire connection? i havent realy found anything about waking up using firedtv remote as far as ive looked. also all setting in bios looks ok and S3 suspend is activated. im just not sure on how to proceed now. thanks in advance.

 

[kszabo]

I had same problem: Antec Fusion goes into standby with remote but does not wake up with remote.

The problem was:
You have to change the cabling of the case! You have to remove the front part, connect the power connector with white-black wires (coming from power button) with the display on the opposite side (it has a two-pin connector with PWR and GRND). Connect the colour-wired (purple-black) power connector coming from display with the motherboard! Antec states that this is the standard config but I have seen 2 Antec Fusion cases till now and both of them were not so configured (the black-white power cable was not connected to the display)

Plus:
BIOS: enable S3 hibernate and wakeup allowed from USB device (I guess not necessary)
configure power management in iMon software (what should happen on power button from remote)
display must have power if PC shut down, there is a 3pin power cable, don´t forget to connect it

 

[snorredick]

aight il try to rewire this tomorrow or whenever i get time, if i remember, il pop in an update if it worked

 

[snorredick]

"Connect the colour-wired (purple-black) power connector coming from display with the motherboard!"

btw, the antec fusion dont have a display, so now im confused again i do have a purple/white cable tho...

 

[kszabo]

"Connect the colour-wired (purple-black) power connector coming from display with the motherboard!"

btw, the antec fusion dont have a display, so now im confused again i do have a purple/white cable tho...

excuse me, I thought you want to do this through the Antecs built-in IR Receiver (part of the Antec´s display you do not have). Forget my advice. As I understand you have a separate IR-Receiver of your TV-Card. I cannot help with that.

 

[snorredick]

yeah, the firedtv tvcard has a builtin ir/remote i wanted to use ty anyway for the advice, always better to get a advice then nothing at all. :]