Reply to thread

Message: <blockquote data-quote="michael01376" data-source="post: 181493" data-attributes="member: 28223">Hi Don,ich hab mal diese ini in einem Forum gefunden.Wo genau weiss ich leider nicht mehr, aber ich komme gut damit zurecht:[CODE]detect_method=43 ;1=black frame, 2=logo, 4=scene change, 8=fuzzy logic, 16=closed captions, 32=aspect ration, 64=silence, 255=all verbose=10 ;show a lot of extra info, level 5 is also OK, set to 0 to disable max_brightness=150 ;frame not black if any pixels checked are greater than this (scale 0 to 255) test_brightness=150 ;frame not pure black if any pixels checked are greater than this, will check average brightness (scale 0 to 255) max_avg_brightness=20 ;lower than 15 for StarTrek ;maximum average brightness for a dim frame to be considered black (scale 0 to 255) 0 means autosetting max_commercialbreak=600 ;maximum length in seconds to consider a segment a commercial break min_commercialbreak=40 ;minimum length in seconds to consider a segment a commercial break max_commercial_size=160 ;maximum time in seconds for a single commercial or multiple commercials if no breaks in between min_commercial_size=20 ;mimimum time in seconds for a single commercial min_show_segment_length=100 ; any segment longer than this will be scored towards show. non_uniformity=1000 max_volume=100 ; any frame with sound volume larger than this will not be regarded as black frame min_silence=10 ; Any deep silence longer than this amount of frames is a possible cutpoint ticker_tape=0 ; Amount of pixels from bottom to ignore in all processing max_repair_size=200 ;### Punsih ### punish=20 ; Compare to average for sum of 1=brightness, 2=uniform 4=volume, 8=silence, 16=schange, set to 0 to disable punish_threshold=1.3 ; Multiply when amount is above average * punish_threshold punish_modifier=2.0 ; When above average * threshold multiply score by this value length_strict_modifier=1.1 length_nonstrict_modifier=1.5 combined_length_strict_modifier=2.0 combined_length_nonstrict_modifier=1.25 logo_present_modifier=1 excessive_length_modifier=0.01 ar_wrong_modifier=1.0 min_schange_modifier=0.5 max_schange_modifier=2.0 schange_threshold=80 cc_commercial_type_modifier=4.0 cc_wrong_type_modifier=2.1 cc_correct_type_modifier=0.75 dictionary_modifier=1.00 intelligent_brightness=0 ; Set to 1 to use a USA specific algorithm to tune some of the settings, not adviced outside the USA give_up_logo_search=2000 ;### Logo ### logo_percentile=0.92 ; if more then this amount of logo is found then logo detection will be disabled logo_threshold=0.50 aggressive_logo_rejection=1 connect_blocks_with_logo=1 ; set to 1 if you want successive blocks with logo on the transition to be regarded as connected, set to 0 to disable cut_on_ar_change=1 ; set to 1 if you want to cut also on aspect ratio changes, set to 0 to disable delete_show_after_last_commercial=1 ; set to 1 if you want to delete the last block if its a show and after a commercial delete_show_before_first_commercial=1 delete_show_before_or_after_current=1 ; set to 1 if you want to delete the previous and the next show in the recording, this can lead to the deletion of trailers of next show shrink_logo=5 ; Reduce the duration of the logo with this amount of seconds after_logo=1 ; set to number of seconds after logo disappears comskip should start to search for silence to insert an additional cutpoint before_logo=1 ; reward=0 padding=0 ms_audio_delay=5 logo_max_percentage_of_screen=0.35 subtitles=0 delete_logo_file=1 ; set to 1 if you want comskip to tidy up after finishing ;### Output ### output_framearray=1 ; create a big excel file for detailed analysis, set to 0 to disable output_videoredo=1 output_womble=0 output_cuttermaran=0 output_mpeg2schnitt=0 output_mpgtx=0 output_zoomplayer_chapter=0 output_zoomplayer_cutlist=0 output_edl=0 output_vcf=0 output_btv=0 ; set to 1 if you want Beyond TV chapter cutlist output output_projectx=0 ; set to 1 if you want ProjectX cutlist output (Xcl) output_demux=0 ; set to 1 if you want comskip to demux the mpeg file while scanning output_bsplayer=1 live_tv=1 ; set to 1 if you use parallelprocessing and need the output while recording dictionary=0 cuttermaran_options="cut=\"true\" unattended=\"true\" muxResult=\"false\" snapToCutPoints=\"true\" closeApp=\"true\"" mpeg2schnitt_options="mpeg2schnitt.exe /S /E /R25 /Z %2 %1[/CODE]GrußMichael</blockquote>

Verification