Frage: beste ini einstellung für ComSkip? (1 Viewer)

[donkarlos]

Hallo,
kann mir jemand saben wie die beste ini einstellung ist dami der werbeschnit am wenigsten übrig lässt?

Oder soll man einfach alles auf "detect_method=255" stellen.
Vielen Dank im voraus.
Gruß
Don

 

[michael01376]

Hi Don,

ich hab mal diese ini in einem Forum gefunden.
Wo genau weiss ich leider nicht mehr, aber ich komme gut damit zurecht:

detect_method=43 ;1=black frame, 2=logo, 4=scene change, 8=fuzzy logic, 16=closed captions, 32=aspect ration, 64=silence, 255=all 
verbose=10 ;show a lot of extra info, level 5 is also OK, set to 0 to disable 
max_brightness=150 ;frame not black if any pixels checked are greater than this (scale 0 to 255) 
test_brightness=150 ;frame not pure black if any pixels checked are greater than this, will check average brightness (scale 0 to 255) 
max_avg_brightness=20 ;lower than 15 for StarTrek ;maximum average brightness for a dim frame to be considered black (scale 0 to 255) 0 means autosetting 
max_commercialbreak=600 ;maximum length in seconds to consider a segment a commercial break 
min_commercialbreak=40 ;minimum length in seconds to consider a segment a commercial break 
max_commercial_size=160 ;maximum time in seconds for a single commercial or multiple commercials if no breaks in between 
min_commercial_size=20 ;mimimum time in seconds for a single commercial 
min_show_segment_length=100 ; any segment longer than this will be scored towards show. 
non_uniformity=1000 
max_volume=100 ; any frame with sound volume larger than this will not be regarded as black frame 
min_silence=10 ; Any deep silence longer than this amount of frames is a possible cutpoint 
ticker_tape=0 ; Amount of pixels from bottom to ignore in all processing 
max_repair_size=200 

;### Punsih ### 

punish=20 ; Compare to average for sum of 1=brightness, 2=uniform 4=volume, 8=silence, 16=schange, set to 0 to disable 
punish_threshold=1.3 ; Multiply when amount is above average * punish_threshold 
punish_modifier=2.0 ; When above average * threshold multiply score by this value 


length_strict_modifier=1.1 
length_nonstrict_modifier=1.5 
combined_length_strict_modifier=2.0 
combined_length_nonstrict_modifier=1.25 
logo_present_modifier=1 
excessive_length_modifier=0.01 
ar_wrong_modifier=1.0 
min_schange_modifier=0.5 
max_schange_modifier=2.0 
schange_threshold=80 
cc_commercial_type_modifier=4.0 
cc_wrong_type_modifier=2.1 
cc_correct_type_modifier=0.75 
dictionary_modifier=1.00 


intelligent_brightness=0 ; Set to 1 to use a USA specific algorithm to tune some of the settings, not adviced outside the USA 
give_up_logo_search=2000 


;### Logo ### 

logo_percentile=0.92 ; if more then this amount of logo is found then logo detection will be disabled 
logo_threshold=0.50 
aggressive_logo_rejection=1 
connect_blocks_with_logo=1 ; set to 1 if you want successive blocks with logo on the transition to be regarded as connected, set to 0 to disable 
cut_on_ar_change=1 ; set to 1 if you want to cut also on aspect ratio changes, set to 0 to disable 
delete_show_after_last_commercial=1 ; set to 1 if you want to delete the last block if its a show and after a commercial 
delete_show_before_first_commercial=1 
delete_show_before_or_after_current=1 ; set to 1 if you want to delete the previous and the next show in the recording, this can lead to the deletion of trailers of next show 
shrink_logo=5 ; Reduce the duration of the logo with this amount of seconds 
after_logo=1 ; set to number of seconds after logo disappears comskip should start to search for silence to insert an additional cutpoint 
before_logo=1 ; 
reward=0 
padding=0 
ms_audio_delay=5 
logo_max_percentage_of_screen=0.35 
subtitles=0 
delete_logo_file=1 ; set to 1 if you want comskip to tidy up after finishing 


;### Output ### 

output_framearray=1 ; create a big excel file for detailed analysis, set to 0 to disable 
output_videoredo=1 
output_womble=0 
output_cuttermaran=0 
output_mpeg2schnitt=0 
output_mpgtx=0 
output_zoomplayer_chapter=0 
output_zoomplayer_cutlist=0 
output_edl=0 
output_vcf=0 
output_btv=0 ; set to 1 if you want Beyond TV chapter cutlist output 
output_projectx=0 ; set to 1 if you want ProjectX cutlist output (Xcl) 
output_demux=0 ; set to 1 if you want comskip to demux the mpeg file while scanning 
output_bsplayer=1 
live_tv=1 ; set to 1 if you use parallelprocessing and need the output while recording 
dictionary=0 
cuttermaran_options="cut=\"true\" unattended=\"true\" muxResult=\"false\" snapToCutPoints=\"true\" closeApp=\"true\"" 
mpeg2schnitt_options="mpeg2schnitt.exe /S /E /R25 /Z %2 %1

Gruß
Michael

 

[erik1958]

Dies ist ein sehr aggressiever ini file.
Es werde vielleigt besser mit dem default ini file an zu fangen.

Und setze
output_framearray=0
order sie becommen einen sehr grossen .csv file
(main deutsch ist nicht so guht)