Reply to thread

Message

<blockquote data-quote="RonD" data-source="post: 1147093" data-attributes="member: 117536">Found time to test this on my local MP1 setup. Your grabber works fine when I test, so now we need to understand what is causing problems. For the tests I did the following1. Saved your imdb_com.xml, renamed to www_imdb_com_53158.xml so I can tell what I'm using. Copied to grabbers/US folder C:\ProgramData\Team MediaPortal\MediaPortal TV Server\WebEPG\grabbers\US2. started TV Config, went to WebEPG &gt; TV Mappings, did import for &quot;Favorites&quot; to load my channels, deleted all but 4 test channels, see WebEPGimport.PNG3. did AutoMap since this is setup for my zipcode, did a manual Clear Mapping for 2 channels I will use to test your 53158.xml file see WebEPGautomap.PNG. If you press AutoMap it should work for your setup at this point.4. since your channels don't map to my SanFranBay TV channels, used manual map so KRON-HD = 5, KTVU-HD = 6 to test your grabber file, see WebEPG_53158.PNG this is special testing only step so I can test drive 53158.xml5. went to WebEPG &gt; General, pressed Save (very important to press Save) set GrabDays=2 just for test, then GrabNow, waited till done, checked&nbsp; MP1 EPG and see your channels KTVU=Fox6, KRON=NBC5, and my channels KGO=ABC7, KPIX=KPIX5 in EPGSo the key question is does step #3 have problems when you try? Follow the steps #1 to #3 I showed, skip #4 I did that to use both grabbers for testing. In step #5 make sure you pressed Save and does this work? In #3, get screen shot of what happens after you do AutoMap.If step #3 still does not AutoMap, make a zip of all log files and upload so I can take a look.</blockquote>

[QUOTE="RonD, post: 1147093, member: 117536"] Found time to test this on my local MP1 setup. Your grabber works fine when I test, so now we need to understand what is causing problems. For the tests I did the following 1. Saved your imdb_com.xml, renamed to www_imdb_com_53158.xml so I can tell what I'm using. Copied to grabbers/US folder [B]C:\ProgramData\Team MediaPortal\MediaPortal TV Server\WebEPG\grabbers\US[/B] 2. started TV Config, went to WebEPG > TV Mappings, did [B]import [/B]for "Favorites" to load my channels, deleted all but 4 test channels, see WebEPGimport.PNG 3. did [B]AutoMap [/B]since this is setup for my zipcode, did a manual [B]Clear Mapping[/B] for 2 channels I will use to test your 53158.xml file see WebEPGautomap.PNG. If you press [B]AutoMap [/B] it should work for your setup at this point. 4. since your channels don't map to my SanFranBay TV channels, used manual map so KRON-HD = 5, KTVU-HD = 6 to test your grabber file, see WebEPG_53158.PNG this is special testing only step so I can test drive 53158.xml 5. went to WebEPG > General, pressed [B]Save [/B](very important to press [B]Save[/B]) set GrabDays=2 just for test, then [B]GrabNow[/B], waited till done, checked MP1 EPG and see your channels KTVU=Fox6, KRON=NBC5, and my channels KGO=ABC7, KPIX=KPIX5 in EPG So the key question is does step #3 have problems when you try? Follow the steps #1 to #3 I showed, skip #4 I did that to use both grabbers for testing. In step #5 make sure you pressed [B]Save [/B]and does this work? In #3, get screen shot of what happens after you do AutoMap. If step #3 still does not AutoMap, make a zip of all log files and upload so I can take a look. [/QUOTE]

Verification