Reply to thread

Message

<blockquote data-quote="rojoyinc" data-source="post: 699019" data-attributes="member: 109509">I finally got MP installed and running fairly nicely.&nbsp; Quite confused when installing, I went into installing everything I could think of and once working.&nbsp; (well now I want to remove what I don't need).For example - I had&nbsp; IR suite running,&nbsp; Girder, and MP remote plug ins... (quite a mess) but once it worked. I started to remove things. I've removed, girder, ir-suite, and a IR server plugin I didn't think I was using.What I think is working (bare bones) is in TV server conf. I have&nbsp; Plug-ins&nbsp; &quot;TV3 Blaster PLuin for IR server&quot; I've removed most everything else.So lets get to the issue.In this plugin - I configured it like this.In PLUG IN SETUP tab (I click STB setup button)TV card1 tab (I only want to get this one working for now).I did a QUICK SETUP and loaded in dish 301/defaults. (Which seem to work). PRELOADED for my VIP 222k STB.I have MS wait between digits at 300&nbsp; (works, I didn't really adjust other than taking it down from 400)No pre-change commandno send select commandno send select twice checkedchannel digits &quot;simple&quot; (which I think it just the ones I enter for example channel 3 is 3 rather than 003?)repeat 0repeat delay 0Below it says TEST I enter a change and click test and the channel changes.&nbsp; (I'm doing this on my desktop in basement, it sends IR to my USB-IRT upstairs which blasts the STB.&nbsp; ALL IT WELL!&nbsp;&nbsp; the channel changes nicely.(I leave Marco's and IR command tabs blank)Click OK - run MP.TV on - watching MP and TV inset on my desktop. (Or upstairs on TV).&nbsp; key in the channel on my keypad.&nbsp; &quot;3&quot;.I see the STB respond with&nbsp; 3333...333&nbsp;&nbsp; or some such. (more than once)&nbsp; I suspect if I turn on&nbsp; 3 digital channels it might display 003&nbsp; 003 003 and that might work, but I don't want the repeats.&nbsp;&nbsp; As is - it tries to change the channel to 333. (which is a sub channel on dish and I have to run up to the STB to&nbsp; hit PREV to get back out of it.If I change channel to say&nbsp; 186... it works, but I see it entered 2-3 times.I've searched all over for where the repeats could be configured in. any ideas!?&nbsp; <img src="data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7" class="smilie smilie--sprite smilie--sprite8" alt=":D" title="Big Grin&nbsp; &nbsp; :D" loading="lazy" data-shortname=":D" />P.S.&nbsp; Inside media portal config.&nbsp; I have&nbsp;&nbsp; IR blast zone plugin (enabled)&nbsp; do I need this?I have MP control plugin for IR server (enabled) do I need this?I wonder if I have repetitive configs that are duplicating my comamnds.I have USB-UIRT (under remote) toggled off) only because it says driver not loaded) when it is. Seems to conflict with something else, because I've seen it display the driver doing my last week or configuring.</blockquote>

[QUOTE="rojoyinc, post: 699019, member: 109509"] I finally got MP installed and running fairly nicely. Quite confused when installing, I went into installing everything I could think of and once working. (well now I want to remove what I don't need). For example - I had IR suite running, Girder, and MP remote plug ins... (quite a mess) but once it worked. I started to remove things. I've removed, girder, ir-suite, and a IR server plugin I didn't think I was using. What I think is working (bare bones) is in TV server conf. I have Plug-ins "TV3 Blaster PLuin for IR server" I've removed most everything else. So lets get to the issue. In this plugin - I configured it like this. In PLUG IN SETUP tab (I click STB setup button) TV card1 tab (I only want to get this one working for now). I did a QUICK SETUP and loaded in dish 301/defaults. (Which seem to work). PRELOADED for my VIP 222k STB. I have MS wait between digits at 300 (works, I didn't really adjust other than taking it down from 400) No pre-change command no send select command no send select twice checked channel digits "simple" (which I think it just the ones I enter for example channel 3 is 3 rather than 003?) repeat 0 repeat delay 0 Below it says TEST I enter a change and click test and the channel changes. (I'm doing this on my desktop in basement, it sends IR to my USB-IRT upstairs which blasts the STB. ALL IT WELL! the channel changes nicely. (I leave Marco's and IR command tabs blank) Click OK - run MP. TV on - watching MP and TV inset on my desktop. (Or upstairs on TV). key in the channel on my keypad. "3". I see the STB respond with 3333...333 or some such. (more than once) I suspect if I turn on 3 digital channels it might display 003 003 003 and that might work, but I don't want the repeats. As is - it tries to change the channel to 333. (which is a sub channel on dish and I have to run up to the STB to hit PREV to get back out of it. If I change channel to say 186... it works, but I see it entered 2-3 times. I've searched all over for where the repeats could be configured in. any ideas!? :thx: P.S. Inside media portal config. I have IR blast zone plugin (enabled) do I need this? I have MP control plugin for IR server (enabled) do I need this? I wonder if I have repetitive configs that are duplicating my comamnds. I have USB-UIRT (under remote) toggled off) only because it says driver not loaded) when it is. Seems to conflict with something else, because I've seen it display the driver doing my last week or configuring. [/QUOTE]

Verification