home
products
contribute
download
documentation
forum
Home
Forums
New posts
Search forums
What's new
New posts
All posts
Latest activity
Members
Registered members
Current visitors
Donate
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Forums
MediaPortal 1
Support
General Support
Low quality when watching TV
Contact us
RSS
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Spragleknas" data-source="post: 205054" data-attributes="member: 17435"><p>First: The PVR-500 come in two flavors - one with "good" TV-chips and one with not-so-good (if I remember correct)</p><p>Hope you got the good one. Try googling</p><p></p><p>You should state what codec you use, and how you connect to the TV-card (antenna, s-video, composite).</p><p></p><p>You should try higher bit-rate for the TV-cards. You can set this in setup.exe -> TV -> TV-card /EDIT -> Quality control</p><p></p><p>or</p><p></p><p>1: DL GraphEdit - <a href="http://en.wikipedia.org/wiki/GraphEdit" target="_blank">http://en.wikipedia.org/wiki/GraphEdit</a></p><p>2: Unzip and open graphedit (GraphEdt)</p><p>(Cut 'n paste + edit)</p><p>Using GraphEdit, go to: Graph > Insert Filters > Multiplexer Devices > Hauppauge WinTV PVR PCI II Encoder and Insert Filter. (Or simular!!!)</p><p>Then right click on the filter and select properties. Under the "Hauppauge ECP Video" tab change the Bitrate Average to "8000", the Peak to "12000"</p><p></p><p>See my post here: <a href="http://www.diskusjon.no/index.php?showtopic=810815" target="_blank">http://www.diskusjon.no/index.php?showtopic=810815</a></p><p>(Norwegian)</p><p></p><p>It seems that de-interlacing is poor on you attached picture...</p></blockquote><p></p>
[QUOTE="Spragleknas, post: 205054, member: 17435"] First: The PVR-500 come in two flavors - one with "good" TV-chips and one with not-so-good (if I remember correct) Hope you got the good one. Try googling You should state what codec you use, and how you connect to the TV-card (antenna, s-video, composite). You should try higher bit-rate for the TV-cards. You can set this in setup.exe -> TV -> TV-card /EDIT -> Quality control or 1: DL GraphEdit - [url]http://en.wikipedia.org/wiki/GraphEdit[/url] 2: Unzip and open graphedit (GraphEdt) (Cut 'n paste + edit) Using GraphEdit, go to: Graph > Insert Filters > Multiplexer Devices > Hauppauge WinTV PVR PCI II Encoder and Insert Filter. (Or simular!!!) Then right click on the filter and select properties. Under the "Hauppauge ECP Video" tab change the Bitrate Average to "8000", the Peak to "12000" See my post here: [url]http://www.diskusjon.no/index.php?showtopic=810815[/url] (Norwegian) It seems that de-interlacing is poor on you attached picture... [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
MediaPortal 1
Support
General Support
Low quality when watching TV
Contact us
RSS
Top
Bottom
