Reply to thread

Message

<blockquote data-quote="RonD" data-source="post: 1077008" data-attributes="member: 117536">In the other MePo thread, LAV 0.58.2 TV codec with the new(er) CoreCC 20130727 file worked with MePo 1.5.0 and I could watch live or recorded USA ATSC and see CC. This also worked with the Cyberlink PDVD codecs. Based on the CC wiki I was a little surprised LAV worked. The ATSC CC working configuration wasVideoPostProcessing &gt; CoreCC 20130727 = EnabledTV mpeg2 codec = LAV or Cyberlink PDVDAfter updating to MePo 1.7.0, with LAV0.61.2 and using CoreCC 20130727, I hoped/expected ATSC CC would still work, but no luck. This configuration is alsoVideoPostProcessing &gt; CoreCC 20130727 = EnabledTV mpeg2 codec = LAV or MsftDTV-DVDNot sure why CoreCC shows up as an option for TV mpeg2 codec. I don't remember seeing that in 1.5.0. See Config_CoreCC.PNG. But since the &quot;wiki config&quot; for 1.7.0 did not work I said WTF lets see what happens. I was even more surprised this worked at all and assumed somewhere in MePo 1.6.0 or 1.7.0 this was defined as the &quot;new correct&quot; config. This configuration works for most cases until I stumbled over the 720p/1080i weird^2 stuff on Sunday morning.VideoPostProcessing &gt; CoreCC 20130727 = EnabledTV mpeg2 codec = CoreCC but uses MsftDTV-DVDSomewhere I downloaded/installed GraphStudio and looked at the working ATSC/CC config in the other thread. I'll have to find where I did this and get it setup again. The 1st question is why doesn't the &quot;wiki config&quot; work for 1.7.0 with LAV. Then what happens when I do&nbsp; the 720p/1080i switch. There is some other weird stuff going on my Win8 MePo 1.7.0 system.This all goes back to rule #1, &quot;if it ain't broke, don't fix it&quot; in this case upgrading from 1.5.0 to 1.7.0.</blockquote>

[QUOTE="RonD, post: 1077008, member: 117536"] In the other MePo thread, LAV 0.58.2 TV codec with the new(er) CoreCC 20130727 file worked with MePo 1.5.0 and I could watch live or recorded USA ATSC and see CC. This also worked with the Cyberlink PDVD codecs. Based on the CC wiki I was a little surprised LAV worked. The ATSC CC working configuration was VideoPostProcessing > CoreCC 20130727 = Enabled TV mpeg2 codec = LAV or Cyberlink PDVD After updating to MePo 1.7.0, with LAV0.61.2 and using CoreCC 20130727, I hoped/expected ATSC CC would still work, but no luck. This configuration is also VideoPostProcessing > CoreCC 20130727 = Enabled TV mpeg2 codec = LAV or MsftDTV-DVD Not sure why CoreCC shows up as an option for TV mpeg2 codec. I don't remember seeing that in 1.5.0. See Config_CoreCC.PNG. But since the "wiki config" for 1.7.0 did not work I said WTF lets see what happens. I was even more surprised this worked at all and assumed somewhere in MePo 1.6.0 or 1.7.0 this was defined as the "new correct" config. This configuration works for most cases until I stumbled over the 720p/1080i weird^2 stuff on Sunday morning. VideoPostProcessing > CoreCC 20130727 = Enabled TV mpeg2 codec = CoreCC but uses MsftDTV-DVD Somewhere I downloaded/installed GraphStudio and looked at the working ATSC/CC config in the other thread. I'll have to find where I did this and get it setup again. The 1st question is why doesn't the "wiki config" work for 1.7.0 with LAV. Then what happens when I do the 720p/1080i switch. There is some other weird stuff going on my Win8 MePo 1.7.0 system. This all goes back to rule #1, "if it ain't broke, don't fix it" in this case upgrading from 1.5.0 to 1.7.0. [/QUOTE]

Verification