Reply to thread

Message

<blockquote data-quote="carlo_0000" data-source="post: 876689" data-attributes="member: 101671">hello&nbsp;i had some trouble with my previous instalation (mediaportal 1.2.1 if i remember)so i maked a new one with 2 servers&nbsp;i had some strange probleme,&nbsp; i was unable to watch hdtv channel, it was glitching, video looks corrupti searched why,the signal from sat was good enougth, codec was ok too, network ok tooafter that i defragmented the hard drive, i thought i was resolved but afer 15-20 min watching it goes crazy again&nbsp;i had olso some diseqc problem, the diseqc did it never very good with mediaportal but it was working mostly&nbsp;2 with diseqc 4 lnb &quot;maximum high iso switch&quot;i have an knc dvb-s2 (diseq did work mostly normaly)and an omicom dvb-s2 (harder to switch , sometime i have to try 2 or 3 times,i had to move to a channel from an other satelite and come back to the desired one, and repet if neededwith bda driver&nbsp; under windows 2003 server&nbsp;the lnb3 on the omicom&nbsp; didn't work from longer time, so i thought&nbsp; the problem was outside,&nbsp; humidity or something like that in my cables or in the diesqc and sometime had trouble on lnb one&nbsp;&nbsp;but now none of the diesqc are working&nbsp;so i deside to clean all, remove the 2 diseqc put one cable on astra 19&nbsp;i tried to upgrad the computer to win7&nbsp; but no luck, computer too old , was not stablei olso suspected maybe the power suply&nbsp; was faulty&nbsp;so i change the computer under windows 7 (so it s ready for mp2)&nbsp;but still no luck for the diesqc, none of them is working&nbsp;i decided to test them with dvbdream, i tested astra 19 cable on the 4 input , and one&nbsp; the 2 diesqcall input did it ok&nbsp;but in mediaportal it s not working anymorewhen i last use for exemple&nbsp; input 3 with dvbdream and&nbsp; close itback to mediaportal&nbsp; then only&nbsp; input 3 is working and not able to switch to anther one&nbsp;&nbsp;i olso want to use an other tv server&nbsp;&nbsp; with my nova stik usb dvb-tbeacuse antena cable is too long for the master server and the signal is to weak on one frequency i needand i alredy have 2 antenna with one preamplifier at maximum with an good cable&nbsp;so i decide to put my segond server close to the antennas, and i had already a computer there for my wireless long range antenna&nbsp;i installed mediaportal 1.2.3&nbsp;&nbsp; (uninstalled msql, because i did a master install first) and notice i did it wrong&nbsp;so after i uninstalled the msql&nbsp;start the tv server configuration, it asked me&nbsp; wath msql server using, so i put ip of the master server&nbsp; named &quot;tv_serveur&quot;&nbsp;all fine , tv service start&nbsp;but now i have some trouble because i only see the master server in the list&nbsp; in tv servers&nbsp; on the 2 computers&nbsp;so what it still wrong ? no slave ?&nbsp;if is stop the tv service on the 2 computers, and start the slave first ,&nbsp; it say me that &quot;tv_serveur&quot; is not reachable&nbsp;&nbsp; use &quot;wifi3&quot; (slave computer)&nbsp; in instead ?i put yesthan i can see&nbsp; wifi3 in tv server list (become the master)&nbsp;i start tv service on the master &quot;tv_serveur&quot; but than i only see wifi3 as master&nbsp;so i can choose one or the other but not the 2 ?what must i do to have wifi3&nbsp; in slave ?&nbsp;thanks for help</blockquote>

[QUOTE="carlo_0000, post: 876689, member: 101671"] hello i had some trouble with my previous instalation (mediaportal 1.2.1 if i remember) so i maked a new one with 2 servers i had some strange probleme, i was unable to watch hdtv channel, it was glitching, video looks corrupt i searched why, the signal from sat was good enougth, codec was ok too, network ok too after that i defragmented the hard drive, i thought i was resolved but afer 15-20 min watching it goes crazy again i had olso some diseqc problem, the diseqc did it never very good with mediaportal but it was working mostly 2 with diseqc 4 lnb "maximum high iso switch" i have an knc dvb-s2 (diseq did work mostly normaly) and an omicom dvb-s2 (harder to switch , sometime i have to try 2 or 3 times,i had to move to a channel from an other satelite and come back to the desired one, and repet if needed with bda driver under windows 2003 server the lnb3 on the omicom didn't work from longer time, so i thought the problem was outside, humidity or something like that in my cables or in the diesqc and sometime had trouble on lnb one but now none of the diesqc are working so i deside to clean all, remove the 2 diseqc put one cable on astra 19 i tried to upgrad the computer to win7 but no luck, computer too old , was not stable i olso suspected maybe the power suply was faulty so i change the computer under windows 7 (so it s ready for mp2) but still no luck for the diesqc, none of them is working i decided to test them with dvbdream, i tested astra 19 cable on the 4 input , and one the 2 diesqc all input did it ok but in mediaportal it s not working anymore when i last use for exemple input 3 with dvbdream and close it back to mediaportal then only input 3 is working and not able to switch to anther one i olso want to use an other tv server with my nova stik usb dvb-t beacuse antena cable is too long for the master server and the signal is to weak on one frequency i need and i alredy have 2 antenna with one preamplifier at maximum with an good cable so i decide to put my segond server close to the antennas, and i had already a computer there for my wireless long range antenna i installed mediaportal 1.2.3 (uninstalled msql, because i did a master install first) and notice i did it wrong so after i uninstalled the msql start the tv server configuration, it asked me wath msql server using, so i put ip of the master server named "tv_serveur" all fine , tv service start but now i have some trouble because i only see the master server in the list in tv servers on the 2 computers so what it still wrong ? no slave ? if is stop the tv service on the 2 computers, and start the slave first , it say me that "tv_serveur" is not reachable use "wifi3" (slave computer) in instead ? i put yes than i can see wifi3 in tv server list (become the master) i start tv service on the master "tv_serveur" but than i only see wifi3 as master so i can choose one or the other but not the 2 ? what must i do to have wifi3 in slave ? thanks for help [/QUOTE]

Verification