home
products
contribute
download
documentation
forum
Home
Forums
New posts
Search forums
What's new
New posts
All posts
Latest activity
Members
Registered members
Current visitors
Donate
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Forums
MediaPortal 1
Support
General Support
Some Problems (Quality record, TVGuide, Remote,...)
Contact us
RSS
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="pierpier1" data-source="post: 26556" data-attributes="member: 16535"><p><strong>MCE2005 remote learning</strong></p><p></p><p>If you have the mce2005 remote that lights up, with two power buttons at the top (one on the left and one on the right) then youmay want to hear that it is a programmable remote.</p><p></p><p>The left power button (labelled TV) adn teh volume up and volume down buttons are programmable to control e.g. your tv on/off and you amp /spdit amp volume.</p><p></p><p>Here is how you do it:</p><p></p><p>1 Place the remote control for Media Center PC head to head (2 to 3 inches apart) with the remote control from which it is learning.</p><p></p><p>2 On the remote control for Media Center PC, press and hold the DVD MENU and OK buttons at the same time until the remote control lights turn off</p><p>(2 seconds).</p><p></p><p>The remote is now in learning setup mode.</p><p></p><p>3 On the remote control for Media Center PC, press and release the TV,</p><p>VOL +, or VOL – button, depending on which command you want it to learn.</p><p>The remote control for Media Center PC lights blink once to confirm the selection.</p><p></p><p>4 On the remote control that is teaching the command, press and hold the button that you want the corresponding button on the remote control for Media Center PC to learn. </p><p></p><p>The remote control for Media Center PC lights blink twice to confirm the selection. If the remote did not learn the command, the lights blink quickly four times. To try again, repeat steps 1 through 4.</p><p></p><p>5 Repeat steps 1 through 4 for the other buttons that can learn commands.</p><p></p><p>To restore the default remote control settings</p><p>1 Press and hold the DVD MENU button and LEFT navigation button at the same time until the remote control for Media Center PC lights turn off.</p><p></p><p>2 Press the OK button.</p><p></p><p>The remote control for Media Center PC lights blink twice to confirm that the buttons have been reset. The TV button will have no command assigned to it and the VOL + and VOL – buttons will adjust the Media Center PC system volume.</p><p></p><p>If the default settings were not restored, the lights blink quickly four times. To try again, repeat steps 1 and 2.</p></blockquote><p></p>
[QUOTE="pierpier1, post: 26556, member: 16535"] [b]MCE2005 remote learning[/b] If you have the mce2005 remote that lights up, with two power buttons at the top (one on the left and one on the right) then youmay want to hear that it is a programmable remote. The left power button (labelled TV) adn teh volume up and volume down buttons are programmable to control e.g. your tv on/off and you amp /spdit amp volume. Here is how you do it: 1 Place the remote control for Media Center PC head to head (2 to 3 inches apart) with the remote control from which it is learning. 2 On the remote control for Media Center PC, press and hold the DVD MENU and OK buttons at the same time until the remote control lights turn off (2 seconds). The remote is now in learning setup mode. 3 On the remote control for Media Center PC, press and release the TV, VOL +, or VOL – button, depending on which command you want it to learn. The remote control for Media Center PC lights blink once to confirm the selection. 4 On the remote control that is teaching the command, press and hold the button that you want the corresponding button on the remote control for Media Center PC to learn. The remote control for Media Center PC lights blink twice to confirm the selection. If the remote did not learn the command, the lights blink quickly four times. To try again, repeat steps 1 through 4. 5 Repeat steps 1 through 4 for the other buttons that can learn commands. To restore the default remote control settings 1 Press and hold the DVD MENU button and LEFT navigation button at the same time until the remote control for Media Center PC lights turn off. 2 Press the OK button. The remote control for Media Center PC lights blink twice to confirm that the buttons have been reset. The TV button will have no command assigned to it and the VOL + and VOL – buttons will adjust the Media Center PC system volume. If the default settings were not restored, the lights blink quickly four times. To try again, repeat steps 1 and 2. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
MediaPortal 1
Support
General Support
Some Problems (Quality record, TVGuide, Remote,...)
Contact us
RSS
Top
Bottom