TBS 6985 No Singal (1 Viewer)

[e123enitan]

Ahhh, that helps!
This is the info I was looking for:

LNB Frequency =10.750

So, the LNB's LOF is 10750 MHz (10.75 GHz).
The correct value to use in the TV Server "band" setting for that LNB would be "Circular".

Two other dishes each have 2 LNB's on each
so in total I have 5 LNB's
I hope I have not complicate issues, I am only concern with first dish 97 west.

If those other dishes are not connected to the same Dreamlink set top box then we don't have to worry about them. Otherwise we'd need to know the correct DiSEqC and/or 22 kHz tone switch settings to use to select the 97W dish.

All the dishes are connected to a switch, i with a single cable out of it, then connected to the DVD box, "yes" I can confirm that all the dishes feeds the box, does that create a complications?
Let me research the your last request further and keep you posted shortly.

The correct info is
DiSEqc SW1.0=4, other dishes/LNBs are on 1,2 and 3, does this helps!

 

[mm1352000]

does this helps!

Yes.
Please follow the instructions in my previous post to install DiSEqC support for your tuner and select the correct setting for scanning.

 

[e123enitan]

does that create a complications?

Unfortunately yes.

So, the first thing you'll need to do is ensure you install the patch from here:
https://forum.team-mediaportal.com/...ther-improvements.103276/page-51#post-1051247

That patch enables (among other things) DiSEqC switch support for TBS tuners.
Install instructions:

1. Open TV Server configuration.
2. Go to the "manual control" section.
3. Click "stop service".
4. Close TV Server configuration.
5. Download the patch from -->here<--.
6. Open Windows Explorer.
7. Navigate to the TV Server install directory (default c:\Program Files (x86)\Team MediaPortal\MediaPortal TV Server).
8. Take a backup of TVLibrary.dll and TvLibrary.Interfaces.dll, just in case.
9. Download and extract the three files in "1.6 patch.rar" into the TV Server install directory, replacing TVLibrary.dll and TvLibrary.Interfaces.dll (TbsCIapi.dll is new; added by the patch).
10. Open TV Server configuration (click "yes" to start the TV service).

I suppose that based on this information:

LNB 22KHz=off
DisEqc SW1.0=4
DisEqc SW1.1=off
Legacy SW=off

...the correct DiSEqC setting for you to use is level 1 BB (which is DiSEqC 1.0 port D/4).

Thanks - let me run through you suggestions and I shall keep you posted I hope it resolves this issue
Cheers!

 

[mm1352000]

Good luck.
I'm going out now, but I'll be back later.

 

[e123enitan]

Good luck.
I'm going out now, but I'll be back later.

Thanks very kind of you, I shall keep you posted

 

[e123enitan]

Good luck.
I'm going out now, but I'll be back later.

Thanks very kind of you, I shall keep you posted

Hi Your recommendations seems to have solved the issue, I can see list of channels, similar to what I have on the dreamlink, know what other setting do need to make to ensure the TV server is running smoothly (such as shift setting, epg etc and how do I configure the client link with the server.
Thanks for your support, that was a quick rescued/effective around solution, I am over impressed.
Its 1 am

 

[e123enitan]

Hi Thz for your assistance, now I have 61 channels listed, so where do I go from here to further the settings to the point that I am able to watch Live TV.

 

[mm1352000]

...so where do I go from here to further the settings to the point that I am able to watch Live TV.

The rest of the setup process is standard, as per the wiki. Please read the wiki setup guides etc.
http://wiki.team-mediaportal.com/1_MEDIAPORTAL_1/13_Setup_Guides

In short, you need to:

1. Configure the connection to the TV Server (wiki notes).
   
2. Configure the codecs to use for TV playback (wiki notes). LAV codecs recommended.
3. Sort out a source for EPG data (wiki notes).

 

[e123enitan]

...so where do I go from here to further the settings to the point that I am able to watch Live TV.

The rest of the setup process is standard, as per the wiki. Please read the wiki setup guides etc.
http://wiki.team-mediaportal.com/1_MEDIAPORTAL_1/13_Setup_Guides

In short, you need to:

1. Configure the connection to the TV Server (wiki notes).
   
2. Configure the codecs to use for TV playback (wiki notes). LAV codecs recommended.
3. Sort out a source for EPG data (wiki notes).

I have gone through above steps, yet I am not able to lunch and watch Live TV, what am missing.

 

[mm1352000]

I have gone through above steps, yet I am not able to lunch and watch Live TV, what am missing.

Sorry, I'm unable to help you as you've given me absolutely nothing to go on. No log files; no screenshots; no details of what happens when you try to view live TV...