- April 10, 2015
- 5
- 0
- Home Country
-
Italy
Thank's for the dll patch. I have the same problem with this card. 
Terratec Cinergy T2 HD Stick DVB-T/T2 not recognized (1 Viewer)
- Thread starter BioEgo
- Start date
- April 10, 2015
- 5
- 0
- Home Country
-
Italy
Now I have a problem with this card. Not load the major DTT Chanel. I have a message: "All card are busy"
- Thread starter
- #13
Hi Maverick,
It happened to me a couple of time while playing around with the settings, usually disconnecting and reconnecting the stick was enough to get it back working again. You can also try to stop and restart TV Service for good measure.
I didn't really pay much attention to this since it happened really only two times so I thought it was just me messing around with something I shouldn't (as usual), so I didn't think it was worth taking the logs ( till now the stick has always been working even after a good amount of sleep-resume cycles and a few reboots), so If you have the logs from TVE you may try to post them maybe there's something useful in there.
HTH,
Regards!
It happened to me a couple of time while playing around with the settings, usually disconnecting and reconnecting the stick was enough to get it back working again. You can also try to stop and restart TV Service for good measure.
I didn't really pay much attention to this since it happened really only two times so I thought it was just me messing around with something I shouldn't (as usual
), so I didn't think it was worth taking the logs ( till now the stick has always been working even after a good amount of sleep-resume cycles and a few reboots), so If you have the logs from TVE you may try to post them maybe there's something useful in there.HTH,
Regards!
- April 10, 2015
- 5
- 0
- Home Country
-
Italy
So I reinstall all package (TV Server and Client). Now working again. It was a bad configuration.
Hi guys!
Have here same card and replaced dll from TVLibrary [tuner_detection_by_node_function].zip
After that in TV Server Configuration appeared "DVB-T Cinergy T2 Stick HD C" and "DVB-T Cinergy T2 Stick HD". But still can't find any channels in scanning. I have tryed both adapters.
Is there something else I should do? I tryed terratec dvbviewer also on same pc and it worked. I attach also logs here, I don't understand if there is seen someting more information?
Have here same card and replaced dll from TVLibrary [tuner_detection_by_node_function].zip
After that in TV Server Configuration appeared "DVB-T Cinergy T2 Stick HD C" and "DVB-T Cinergy T2 Stick HD". But still can't find any channels in scanning. I have tryed both adapters.
Is there something else I should do? I tryed terratec dvbviewer also on same pc and it worked. I attach also logs here, I don't understand if there is seen someting more information?
- Thread starter
- #18
Hi janfin, sorry about that I've rechecked my config and also re-read the full thread to see if I was forgetting something I had done, but that's the only change I've done. Also in posts 4 to 7 of this thread both me and mm1352000 noticed that the card was only working with DVBT (in TVE3) or "specific"(in TVE3.5) provider, while generic was producing the very quick "no signal" output. We did not found a reason for that, but since DVBT was working we just left it there.
Not sure whether it is relevant but looking at your logs I've noticed you have both MP1 and MP2 installed: are you sure the system is using the TVService from MP1 and not MP2? I'm no expert with MP2 and cannot really understand looking at your logs.
Maybe if you have another PC around you can try a clean install of MP1 and see if the card is working there.....
For MP2: using the internal TVE3.5 the card was working (you can see config detail in post 4) without using any patch.
HTH,
Regards!
I've rechecked my config and also re-read the full thread to see if I was forgetting something I had done, but that's the only change I've done. Also in posts 4 to 7 of this thread both me and mm1352000 noticed that the card was only working with DVBT (in TVE3) or "specific"(in TVE3.5) provider, while generic was producing the very quick "no signal" output. We did not found a reason for that, but since DVBT was working we just left it there.Not sure whether it is relevant but looking at your logs I've noticed you have both MP1 and MP2 installed: are you sure the system is using the TVService from MP1 and not MP2? I'm no expert with MP2 and cannot really understand looking at your logs.
Maybe if you have another PC around you can try a clean install of MP1 and see if the card is working there.....
For MP2: using the internal TVE3.5 the card was working (you can see config detail in post 4) without using any patch.
HTH,
Regards!
Hi lads...I know this is little bit off topic,but can you recommend some of DVB-T2 USB tuner MP1? Sorry,but i cant found any post about it...thanks