Recent content by MJGraf

Confirmed working! Set "Show Loading Spinner" back to true - Loading spinner shows and disappears as soon as the video starts. Set BrowserHostWaitTimeout back to 20 seconds and video continues to play after 20 sec. Good job (y) and many thanks! Michael

Many thanks for all your efforts. Just to let you know: A workaround is to set the BrowserHostWaitTimeout to a very high value as described in the first post (I used 60000). But this is just a workaround... And it also supports the thesis that it somehow tries to find out whether the video plays...

Hi @doskabouter, hope you're doing well! Many thanks for all your efforts in keeping this up. Just tested your latest release and in general it works for me. When I delete cookies, I get the "Play me" entry and can enter username and password. After that I can see my profile, etc., and also...

Ja, nicht nur die Option - da ist noch ne Menge alter Code in MediaPortal.Common, der nicht mehr genutzt wird, wenn die Option weg ist. Ich komm nur gerade nicht dazu. Wenn Du willst, nimm gerne die Option schon mal raus und ich kümmere mich später um die Code-Bereinigung...

Hi Spazmodious, you can reset MP2 to the state right after install (actually even a bit before that...) the following way: I assume you have MP2-Server and MP2-Client installed on the same Computer ("Single-Seat"). On that computer, exit the MP2-Client and stop the MP2-Server service (e.g. by...

Thanks for trying! First of all, LocalFileSystem will not work with mapped network drives. This is only for "real" local drives. NetworkNeighborhood "should" work - My suspicion is that for some reason - although you mention that you don't use a password - it requires credentials to be entered...

Hi mperezm77, No. "Server Media Source" just means that the media source is accessed from the MP2-Server - but it may be located on a local drive of the MP2-Server Computer or on a shared drive/Folder in the Network. The opposite is a "Client Media Source". Imagine you have MP2-Server and...

Hi Joe, first of all make sure that LAV filters are intalled - they should have been installed automatically with MP2. Then open the LAV Audio configuration, which should look similar to here and make sure that all audio formats that you want to be streamed bit by bit are checked in the...

That makes our little MP2 really sad :D But thanks anyway for chiming in (y)

Yep - and as the WOL issue is assigned to me, some remarks about it: I started implementing a WOL service because I thought it would be easy to port the MP1 implementation to MP2. Well, that would have been easy, but the MP1 implementation is incomplete - it only supports IPv4 and therefore goes...

Hi pigboy306, may I ask where you put the nfo-files for the ISO-rips? In the same folder as the ISO-files? If so, did you give them the same name as the ISO-files - just with the extension .nfo? I'm asking because nfo-files "should" work for ISO-files. If they don't, you may have found a bug...

Very welcome :) My hope is that MP2 as a whole (in particular ResourceServer, FanArtService and UPnP-Subsystem) can take Advantage of this Speed improvement)...

Thanks, perfect! Not a problem. I have enough of them - and JSchuricht has even more ;) Just want to make sure that for those who have properly tagged files and/or correct nfo-files nothing is broken. Which seems to be the case for you.

Seems like we are getting there :) Very good... I'll have a look at your logs in the next days to see what the reason for the missing 2% is. @Lehmden: it currently looks like the improvements from this thread should go into one of the next weeklies. It would be great if you could throw the...

To install dokan use this installer and start it from commandline with a " /S" switch (capital 'S' is important). That way you set the installation mode to "silent" and at the same time switch off the version check. Hope that helps...