I was a littlebit worried that you had nothing to do with yout spare time [emoji6]
Auto3D plugin for MediaPortal 1.2 - 1.12 (GUI & TV/Beamer) (28 Viewers)
- Thread starter Marcus Venturi
- Start date
- March 23, 2012
- 614
- 745
- 58
- Home Country
-
Germany
- Thread starter
- #742
Hi Wouter, the zoom problem with 3D TAB movies is caused by ViewModeSwitcher. ViewModeSwitcher just cuts off the black bars above and below the movie. I ignores the black bar between the upper and the lower part. After that, the 2 parts are shifted. I will check if I can find a solution for that.
Your other problem with the hanging MediaPortal when turning TV off via Auto3D in suspend is fixed and will be part of the next release.
Your other problem with the hanging MediaPortal when turning TV off via Auto3D in suspend is fixed and will be part of the next release.
Great Marcus. Nice if the TVoff feature works too. Hope you can fix the zooming issue. Would be nice if TAB movies can also be zoomed to full screen with viewmodeswitcher, just as you fixed it for SBS movies.
- March 23, 2012
- 614
- 745
- 58
- Home Country
-
Germany
- Thread starter
- #744
@wouter1971 : OK, modifying ViewModeSwitcher makes no sense, as ViewModeSwitcher knows nothing about 3D movies.
I found a solution in combination of Auto3D and a Core change. Auto3D checks if there is a black bar in a TAB 3D movie. And the Core takes this into consideration when blitting upper / lower part of the image. Can you check if the attached version solves your problem. Don't forget to save your original files, when replacing Core.dll and MediaPortal.exe.
I found a solution in combination of Auto3D and a Core change. Auto3D checks if there is a black bar in a TAB 3D movie. And the Core takes this into consideration when blitting upper / lower part of the image. Can you check if the attached version solves your problem. Don't forget to save your original files, when replacing Core.dll and MediaPortal.exe.
Hi Marcus, i tested it and it does not work behaviour is the same. Sorry.
Remark: when installed the new plugin version removes my old config settings. I have seen this before so i have a backup
Remark: when installed the new plugin version removes my old config settings. I have seen this before so i have a backup
- March 23, 2012
- 614
- 745
- 58
- Home Country
-
Germany
- Thread starter
- #746
Hi Wouter, can you upload a short sequence of a video (about 1 Minute) for me to check?
- March 23, 2012
- 614
- 745
- 58
- Home Country
-
Germany
- Thread starter
- #747
Hi Wouter, can you try with this updated Core.dll again?
Marcus, i tested it again and it does not work. Please take my viewmodeswitcher config file. You will see then that a SBS movie with black bars in it is zoomed perfectly. But with TAB it's shifts completely out of sync when black bar detection is activated. If you need video i will do that tomorrow.
- March 23, 2012
- 614
- 745
- 58
- Home Country
-
Germany
- Thread starter
- #749
Hi Wouter, can you go to the Auto3D setup and check if in "3D Detection" the setting "Video analysis for Top and Bottom (TAB)" is checked?
If not could you retry with this setting enabled and all other checks about naming disabled.
I added my black bar check only to the TAB autodetection for the moment.
If not could you retry with this setting enabled and all other checks about naming disabled.
I added my black bar check only to the TAB autodetection for the moment.
Last edited:
Hi Marcus. I did it and now it seems to adjust something but is with black bar in the middle and it does not switch at the moment.
Update: HOLD your horses. Starting from the begin of the movie makes it work. YES!
Nice!
Update: HOLD your horses. Starting from the begin of the movie makes it work. YES!
Nice!
Last edited: