Auto3D plugin for MediaPortal 1.2 - 1.12 (GUI & TV/Beamer) (12 Viewers)

[conguero23]

I own a sony xbr850b and the register button is greyed out it does not allow me to press it.

 

[Marcus Venturi]

Please set MediaPortal logging to "Debug". Then start the configuration and check if the TV is recognized. After that attach your logfiles to your post.
Maybe I can find something.

 

[conguero23]

The following error occurs:

2015-05-27 18:59:08,247] [Config ] [9 ] [ERROR] - Auto3D: Sequence contains no elements
[2015-05-27 18:59:23,903] [Config ] [9 ] [INFO ] - Auto3D: Sony service found -> Sony Corporation, 192.168.1.5
[2015-05-27 18:59:23,903] [Config ] [9 ] [INFO ] - Auto3D: Sony service connected
[2015-05-27 18:59:23,908] [Config ] [9 ] [ERROR] - Auto3D: Sequence contains no matching element
[2015-05-27 18:59:23,913] [Config ] [9 ] [ERROR] - Auto3D: Action List URL was NOT found for device: BRAVIA XBR-55X850B
[2015-05-27 18:59:23,918] [Config ] [9 ] [INFO ] - Auto3D: Using Registration mode: 3
[2015-05-27 18:59:26,115] [Config ] [9 ] [ERROR] - Auto3D: Sequence contains no elements

 

[Sebastiii]

The following error occurs:

2015-05-27 18:59:08,247] [Config ] [9 ] [ERROR] - Auto3D: Sequence contains no elements
[2015-05-27 18:59:23,903] [Config ] [9 ] [INFO ] - Auto3D: Sony service found -> Sony Corporation, 192.168.1.5
[2015-05-27 18:59:23,903] [Config ] [9 ] [INFO ] - Auto3D: Sony service connected
[2015-05-27 18:59:23,908] [Config ] [9 ] [ERROR] - Auto3D: Sequence contains no matching element
[2015-05-27 18:59:23,913] [Config ] [9 ] [ERROR] - Auto3D: Action List URL was NOT found for device: BRAVIA XBR-55X850B
[2015-05-27 18:59:23,918] [Config ] [9 ] [INFO ] - Auto3D: Using Registration mode: 3
[2015-05-27 18:59:26,115] [Config ] [9 ] [ERROR] - Auto3D: Sequence contains no elements

Better to use watchdog tool and select second option and do what you need and attach the newly created ZIP

 

[conguero23]

Please see included.

 

[Marcus Venturi]

@conguero23 : Logfiles do not contain any debug information. Please go to the MediaPortal Configuration. Then select the General tree node on the left side. In the "General settings" change the "Log verbosity" to "Debug" and repeat the procedure. Then post logfiles again.

 

[conguero23]

I apologize please see the new debug update.

 

[Marcus Venturi]

From what I see in the logfiles everything runs perfect. The TV is recognized and registration is not necessary, therefore the button is grayed out.

Are you able to send commands to the TV via the Sequence Manager?

If that is possible, you should define the sequences necessary to switch the TV into the 3D modes and back. See first thread for some Information about that.

 

[conguero23]

When I try to pair it with my tv it says its not paired. When I try to watch a movie in 3d the menu comes up but does not send the signal to the tv to change to 3d side by side.

 

[Marcus Venturi]

Which menu comes up the, the Auto3D menu, or the menu of your TV?