DVB-IP MediaPortal IPTV Source Filter (14 Viewers)

[georgius]

I cannot find any reason why it doesn't work. Can you try open channel in VLC, leave it playing in VLC a try to scan for same channel in MP?

 

[jacks]

Hi,
I have new strange thing...
When I look tv, if IP network is OK, the network channel is working (DVBIP). If i cut IP Network, and i choose a channel to start, DVB-T is working (if the channel is on DVB-T too). This is OK.

But, if i schedule a program to be recorded in the morning for example, it works if ip network is up , and if i do the same after i cut IP Network (i switch off internet box), MP doesnt recorded anything .

Yo can see example in logs with program "The Hard Corps" fro NRJ12 , scheduled around 00:17 today, witch is not recorded, and when I cancel recording and i view the channel, i can see it correctly.

Thanks

 

[georgius]

Yo can see example in logs with program "The Hard Corps" fro NRJ12 , scheduled around 00:17 today, witch is not recorded, and when I cancel recording and i view the channel, i can see it correctly.

I suppose that you have at least two network cards, one for IPTV provider and another for internet. If you have only one card, than in that case cannot work IPTV filter (it has no connection). RTSP protocol is based on library provided with MP source code and this library is little bit older (and probably with bugs). There was an error while connecting to server, but this library didn't return some useful error. I'm thinking of rewritten RTSP protocol from scratch, but it takes longer time.

In case that you have more than one network cards, cut off your network same as in your post and make these diagnostic information and attach results here:

1. run command line (cmd.exe)
2. enter into command line (without quotes, you should replace path to network.txt file) - it gets your network cards configuration: "ipconfig /all > c:\temp\network.txt"
3. enter into command line (same as previous step) - it gets your network routes: "route print > c:\temp\route.txt"

Common problem of recording in MP 1.1.3 is that MP 1.1.3 tries only first card to record channel. If this first card fail to record channel, MP 1.1.3 tries again same card for recording. But when you stop recording and try to view it works differently. When try to view channel MP 1.1.3 try all cards as defined in configuration to view channel. So, if first card fail, try second card, then third card and so on. In your case it fails two times on DVB-IP card and finally on DVB-T card same channel works.

 

[arj2000]

I cannot find any reason why it doesn't work. Can you try open channel in VLC, leave it playing in VLC a try to scan for same channel in MP?

VLC Ok; MP No signal

 

[georgius]

I cannot find any reason why it doesn't work. Can you try open channel in VLC, leave it playing in VLC a try to scan for same channel in MP?

VLC Ok; MP No signal

Can you try set LogVerbosity in configuration file to 5, try to scan again, post MPIPTVSource.log and set LogVerbosity back?

 

[hola6]

MediaPortal 1.2.0 final (clean installation)
MPIPTVSource 2011-09-13
Imagenio (Spain)
VLC play channels OK (audio & video)

In my case, I get the list from canals but when put them there is black image, soundlessly, and without error message.

With the version 1.0.2 of the IPTV Source Filter I saw without problems Imagenio's canals.

Thanks

 

[georgius]

MediaPortal 1.2.0 final (clean installation)
MPIPTVSource 2011-09-13
Imagenio (Spain)
VLC play channels OK (audio & video)

In my case, I get the list from canals but when put them there is black image, soundlessly, and without error message.

With the version 1.0.2 of the IPTV Source Filter I saw without problems Imagenio's canals.

Thanks

Hi, can you obtain and post logs as described in first post? Without logs is very hard to say where is problem. If is it possible, set verbosity level to 5.

 

[hola6]

How can I set log verbosity in level 5?

 

[georgius]

How can I set log verbosity in level 5?

In configuration file (MPIPTVSource.ini) change LogVerbosity from 3 to 5, save configuration file and try scan again. After scanning change LogVerbosity back to 3.

 

[hola6]

Here my logs.