DVB-S will not add channels (1 Viewer)

Joshdoe2

Portal Member
October 31, 2006
5
0
Home Country
United States of America United States of America
I put together and successfully installed a driver for the Digiwave 103g DVB-S card that I used in Mediaportal. I had spotty scanning success but I did get video playing from one of the unscrambled channels so I know it works.

I have since decided to use TV server and am having no luck scanning when connected directly to my 82 degree Dishpro Circular 112500 LNB (no internal DP switch). I tried using both a standard and Dishpro TPL list that I created and verified in mytheatre but no luck.

I get full quality and signal strength yet the scan reports "No Signal" after each TP scan. I also noticed that it reports "LinearV" after each scan. As I said before, the same setup runs mt no problem (other than that it is is fugly :D ).

Any Ideas? I posted a portion of my tv.log below, any help is appreciated.

11/1/2006 3:17:16 PM TV service started
11/1/2006 3:17:16 PM C:\Documents and Settings\All Users\Application Data\MediaPortal TV Server\gentle.config
11/1/2006 3:17:16 PM ----------------------------
11/1/2006 3:17:16 PM Detected DVB-S card:conexant bda dvb-s tuner/demod
11/1/2006 3:17:16 PM PluginManager: Loaded TV Movie Clickfinder Import version:0.2 author:mPod
11/1/2006 3:17:16 PM PluginManager: Loaded XmlTv version:1.0.0.0 author:Frodo
11/1/2006 3:17:16 PM Controller: Started at server
11/1/2006 3:17:16 PM Controller: local ip adress:192.168.15.102
11/1/2006 3:17:17 PM Controller: server running on server
11/1/2006 3:17:17 PM Controller: setup streaming
11/1/2006 3:17:18 PM dbs:0 channels
11/1/2006 3:17:18 PM EPG: grabber started..
11/1/2006 3:17:18 PM Scheduler: started
11/1/2006 3:17:21 PM Scheduler: loaded 0 schedules
11/1/2006 3:17:21 PM plugin: xmltv started
11/1/2006 3:17:21 PM Controller: initalized
11/1/2006 3:17:32 PM Controller: epg stop
11/1/2006 3:17:32 PM EPG: grabber stopped..
11/1/2006 3:17:39 PM Controller: epg stop
11/1/2006 3:17:46 PM Controller: epg stop
11/1/2006 3:17:46 PM Controller:Tune 1 to
11/1/2006 3:17:46 PM dvbs: Tune:DVBS:tv: Freq:12224000 ONID:-1 TSID:-1 SID:-1 PMT:FFFFFFFF FTA:False LCN:10000 SymbolRate:20000 Polarisation:LinearV DisEqc:None Switch Freq:11700000
11/1/2006 3:17:46 PM BuildGraph
11/1/2006 3:17:46 PM dvb:AddNetworkProviderFilter
11/1/2006 3:17:46 PM dvb:Add DVBSNetworkProvider
11/1/2006 3:17:46 PM CreateTuningSpace()
11/1/2006 3:17:46 PM Found tuningspace Cable
11/1/2006 3:17:46 PM Found tuningspace Antenna
11/1/2006 3:17:46 PM Found tuningspace ATSC
11/1/2006 3:17:46 PM Found tuningspace Digital Cable
11/1/2006 3:17:46 PM Found tuningspace AuxIn1
11/1/2006 3:17:46 PM Found tuningspace FM Radio
11/1/2006 3:17:46 PM Found tuningspace DVB-T
11/1/2006 3:17:46 PM Found tuningspace MediaPortal DVB-S
11/1/2006 3:17:46 PM Found tuningspace DVBS TuningSpace
11/1/2006 3:17:46 PM Found correct tuningspace DVBS TuningSpace
11/1/2006 3:17:46 PM dvb:Add MPEG2 Demultiplexer filter
11/1/2006 3:17:46 PM dvb:add Inf Tee filter
11/1/2006 3:17:46 PM dvb:AddAndConnectBDABoardFilters
11/1/2006 3:17:46 PM dvb: find bda tuner
11/1/2006 3:17:46 PM dvb: -Conexant BDA DVB-S Tuner/Demod
11/1/2006 3:17:46 PM dvb: OK
11/1/2006 3:17:46 PM dvb:find bda receiver
11/1/2006 3:17:46 PM dvb: -Conexant 2388x Transport Stream Capture
11/1/2006 3:17:46 PM dvb:OK
11/1/2006 3:17:46 PM dvb:connect mpeg-2 demuxer to maintee
11/1/2006 3:17:46 PM dvb:Add Mediaportal Ts Analyzer filter
11/1/2006 3:17:46 PM Check for Digital Everywhere
11/1/2006 3:17:46 PM Check for Twinhan
11/1/2006 3:17:46 PM Twinhan: check for twinhan driver
11/1/2006 3:17:46 PM Check for TechnoTrend
11/1/2006 3:17:46 PM dvb:AddTransportStreamFiltersToGraph
11/1/2006 3:17:46 PM add BDA MPEG2 Transport Information Filter filter
11/1/2006 3:17:46 PM add MPEG-2 Sections and Tables filter
11/1/2006 3:17:46 PM pinTif:name:Input Direction:Input
11/1/2006 3:17:46 PM pinSec:name:In Direction:Input
11/1/2006 3:17:46 PM Connect tif and mpeg2 sections and tables
11/1/2006 3:17:46 PM dvb:try tif:name:1 Direction:Output
11/1/2006 3:17:46 PM tif connected
11/1/2006 3:17:46 PM try sections&tables:name:4 Direction:Output
11/1/2006 3:17:46 PM dvb:mpeg 2 sections and tables not connected:0x80040217
11/1/2006 3:17:46 PM try sections&tables:name:5 Direction:Output
11/1/2006 3:17:46 PM mpeg 2 sections and tables connected
11/1/2006 3:17:46 PM dvb: GetTunerSignalStatistics()
11/1/2006 3:17:46 PM dvb:confused:ubmitTuneRequest
11/1/2006 3:17:47 PM Controller: Tuner locked:False signal strength:0 signal quality:0
11/1/2006 3:17:47 PM dvbs: Tune:DVBS:tv: Freq:12224000 ONID:-1 TSID:-1 SID:-1 PMT:FFFFFFFF FTA:False LCN:10000 SymbolRate:20000 Polarisation:LinearV DisEqc:None Switch Freq:11700000
11/1/2006 3:17:47 PM dvb:confused:ubmitTuneRequest
11/1/2006 3:17:47 PM dvb:RunGraph
11/1/2006 3:17:47 PM Scan: signal status update took 78.125 msec
11/1/2006 3:17:50 PM Signal detected, wait for good signal quality
11/1/2006 3:17:53 PM Scan! timeout...found no channels
11/1/2006 3:17:53 PM dvbs: Tune:DVBS:tv: Freq:12253000 ONID:-1 TSID:-1 SID:-1 PMT:FFFFFFFF FTA:False LCN:10000 SymbolRate:20000 Polarisation:LinearV DisEqc:None Switch Freq:11700000
11/1/2006 3:17:53 PM dvb:confused:ubmitTuneRequest
11/1/2006 3:17:53 PM dvb:RunGraph: already running
11/1/2006 3:17:53 PM Scan: signal status update took 62.5 msec
11/1/2006 3:17:55 PM Signal detected, wait for good signal quality
11/1/2006 3:17:58 PM Scan! timeout...found no channels
11/1/2006 3:17:58 PM dvbs: Tune:DVBS:tv: Freq:12282000 ONID:-1 TSID:-1 SID:-1 PMT:FFFFFFFF FTA:False LCN:10000 SymbolRate:20000 Polarisation:LinearV
 

mikeahmed

New Member
August 6, 2006
2
0
Hi there,
Would it be possible to get 103G driver from you. I'm having trouble getting 103g works under mediaportal. Thanks in advance!

Mike
 

Joshdoe2

Portal Member
October 31, 2006
5
0
Home Country
United States of America United States of America
Sorry about the delay but I scrapped TV Server until they fix LNB support for us North Americans. Nothings burns me more to see every little bug under the sun fixed except for LNB support ESPECIALLY when it is kinda works in Media Portal.

I even offered up $50.00 for them to look at it. Yeah I know it is not much but about the cost of a commercial application. In any case, enough ranting, I am just frustrated by the potential of this app. not being fully realized.

The file was verified to work in both Media Portal for the Geniatech Digister/ Digiwave 103g (same card). The only problem is I don't know how to attach a file. I had sent the file and TPL's I created fro North America to Daniel. He told me they where included in the next build.

So how do I attach a file?
 

Joshdoe2

Portal Member
October 31, 2006
5
0
Home Country
United States of America United States of America
Any progress for us North Americans? Has the diseqc functionality of MediPortal been added to the TV server?
 

JoeNezZ

New Member
September 8, 2007
1
0
61
I guess that means no, as 2.3_RC2 detect my card as a geniatec dvbs digistar but will only allow 1 lnb, & will not find any channels when it scans.
setup is single line no switch legacy circular LNB freq:11250

the problem as I see it is this program does not come configured for north american use & the setup wizard does not allow the user to adjust any of the paramiters like "My Theatre" or "Prog DVB" both of witch will run fine but have poor video quality compaied to "linux VDR"

I am looking for a high quality DVB program that will support my card for the windows platform.

Is there any way to manually adjust the setup paramiters of media portal & get it to scan channels ?
 

EMKO

Portal Pro
May 4, 2006
175
3
i also have a 103g i can get it to scan but it will only scan 1sat wont scan the other 3 i have can this be fixed ?
not saying that its bad just asking if someone could make a fix for us that use the digiwave 103g.

i use tv-server each dieqc setting will give out the same sat channel it wont switch to the correct one.

,thanks
 

infinite.loop

Retired Team Member
  • Premium Supporter
  • December 26, 2004
    16,163
    4,133
    127.0.0.1
    Home Country
    Austria Austria
    i also have a 103g i can get it to scan but it will only scan 1sat wont scan the other 3 i have can this be fixed ?
    not saying that its bad just asking if someone could make a fix for us that use the digiwave 103g.

    i use tv-server each dieqc setting will give out the same sat channel it wont switch to the correct one.
    if you have more then 1 LNBs (tuning more then 1 sats) then you need a TV-Card where LNB-selecttion / switching is supported.

    see :: this list::
     

    Users who are viewing this thread

    Top Bottom