Tuner does not resume after standby (1 Viewer)

[girgises]

I just started using MP last week. I have worked on it to get everything to work (through the help of this forum) but it records a non tuned picture when it resumes from standby. The Scheduler plugin works on occassions and very rarely. I found it much easier to use the PVR Plugin which does work seamlessly. However it wakes the computer starts MP and starts to record the correct channel however it is just a snowy picture (non tuned). It will work if the computer is on and MP is on and records perfect picture. I have tried turning MP off before going to standby but no change. I have not tried hibernate because if you put the computer in Hibernate you cannot wake it with the remote. When you start MP normally the picture comes on perfect.

I have a Celeron 2.6 with 256 of RAM. I am using the Hauppauge PVR USB2.

 

[Paranoid Delusion]

girgises

powerscheduler has had a lot of work done to it.
If using 0.2RC4 try updating with a svn 04-27-2006 seems to be good.
If still having problems, post back using the hardware template found here, with more info.
https://forum.team-mediaportal.com/viewtopic.php?t=6438

 

[girgises]

Area: Media Portal Program / Media Portal Documentation / Media Portal Skin / Plugins / Other
MP Version: RC4
Skin: MCE
Windows Version: Windows XP home sp2
CPU Type: Intel Cel 2.6 gg Memory: 256
Motherboard Chipset: manufacturer and model
Video Card: manufacturer and model
Video Card Driver: driver version you used for testing
Video Card Resolution: your desktop resolution
Video Render Type: VMR9 or Overlay
Video Codec Type & Version: video codec you used for testing
Audio Codec Type & Version: audio codec you used for testing
TV Card: type of TV card, Hauppauge PVR 150 USB 2
TV Card Type: software / hardware / DVB
TV Card Driver: driver version you used for testing

I tried to install the latest SVN and that did not help my situation. Anyway I did get the computer to go to standby and wake up for the recordings and start recording the correct channel using the PVR-Scheduler Plugin but it still does not get the tuner to bring in the picture only a snowy non-tuned picture. I also noted that if you try to run the setup wizard it says that it is analog and finds about 9 channels. However when you run it from the MP setup it finds all the channels correctly. Could that be the problem?

 

[girgises]

Area: Media Portal Program
MediaPortal Version: 0.2.0.0 RC4 (2006-04-18)
MediaPortal Skin: MCE
Windows Version: Windows XP (SP2)
.NET CLR Version: 2.0.50727
DirectX Version: 4.09.00.0904 (9.0c)
Audio Codec: MPEG/AC3/DTS/LPCM Audio Decoder
Video Codec: DScaler Mpeg2 Video Decoder
CPU Type: Intel Celeron - 2.53GHz
Memory: 253 MB
Motherboard: 0WF887 (Dell Computer Corp.)
TV Card Model: hauppauge PVR 150 USB2
TV Card Type: -
TV Card Driver: -
Video Card Model: Intel(r) 82865g Graphics Controller (96 MB)
Video Card Driver: -
Video Card Resolution: 1024x768
Video Render Type: -
Audio Card Model: SoundMAX Integrated Digital Audio
Audio Card Driver: -
Synopsis::

Only 9 out of 88 channels are recognized by MP when resuming from standby for recording. Although during normal operation all 88 channels can be viewed.

 

[hollifm]

Has there been any progress on this issue

I have just started using the MP and found it very useful. Problem is when MP either goes to Standby or Hibernate it will upon waking up record snow. I have to shut down MP to get the channels back. I have a PVR150.

 

[wewe]

what does TV do when you standby and resume by hand? There is an error that causes "black screen after resume". I have it when using the autostart plugin.

I think it is caused by a directX error. Do you have an error in your log called "D3DERR_DEVICELOST"?

thanks+regards
WeWe

 

[ronilse]

Hi,
The D3DERR_DEVICELOST error MP can handle (if you got a D3DERR_INVALIDCALL, that will cause trouble), I have D3DERR_DEVICELOST in my log too & no black screen after hibernating.

girgises:
Make sure that the card has the nessesary "Antenna / cable" option selected in MP Setup -> Television -> Capture Cards -> your card & Edit.

Regards
Roy

 

[Dado]

Same error D3D

Hi,
I have the error D3DERR_DEVICELOST when pc going to suspend, but all works after resume from standby...
However how can I do for delete this D3D error?

This error is in my MP logs from about three months....

I have configured Antenna (that is correct).

Thanks,
Dado

 

[ronilse]

Re: Same error D3D

Hi,
I have the error D3DERR_DEVICELOST when pc going to suspend, but all works after resume from standby...
However how can I do for delete this D3D error?

This error is in my MP logs from about three months....

I have configured Antenna (that is correct).

Thanks,
Dado

The error cames every time on a standby / hibernate situation & for now you can't get rid of it, but it does not harm you system either

Regards
Roy

 

[Elf]

Can I add my voice to this one - I'm using 0.2.0.0 with a DVB-T tuner and getting blank TV when resuming from either standby or hibernate. The TV picture is completely black and there is no sound. Everything else works just fine. Once it has happened, shutting down MP and restarting it still doesn't work, I need to cold boot the machine to see any TV again...