IMON support (3 Viewers)

[chemelli]

The buttons I tested seems to do. Some don't, but I suggest it's a kind of mapping problem, because a log entry like "Abstract Remote Button not found: iMon USB (1252)" is done.

Der_Bub,

1252 is not mapped because is not part of the default MCE buttons I think.

Please test all buttons that are common to a MCE remote. Take care that you have to learn how to use teletext buttons ( red, yellow, green and blue )

Simone

 

[chemelli]

I had minidisplay totally deactivated through testing.

New version going to be uploaded...

Please check carefully that all is removed from the previous one and that Debug Client is able to receive command, before testing in mp plugin and later in MP.

Simone

 

[disaster123]

chemelli
as i already wrote IRS was never installed before so is nothing to remove from previous ones. I'm now debugging with Pretoriano via IRC - hope that helps. What do you mean with debug client is able to receive commands - nothing happens in debug client absolutely nothing...

 

[disaster123]

Here are my logs from Bus Hounter from my NON HID client - not tested this client with IRRS.

 

[Der_Bub]

Unfortunatly the IRSS Server has the same Problems like the ImonManager with my Harmony One Remote: With ImonPad config the Buttons react a little bit slowly and imprecise If I set MCE mode in ImonManager everything is smooth and fast, unfortunatly it doesn't work after disconecting System from AC-Power and rebooting.

Soon i will upload a new version with another sensitivity improvement but i belive the issue with the slow buttons (directional keys sensitivity has been fixed now and IRSS will have a slider to adjust sensitivity in the future version) is Harmony fault,so can u please test with an original Imon Pad remote if u have one.

Sorry, I forget to mention: I tested the original and IRSS did fine! It's defenitly a Harmony/hardware problem, I was already in contact with the harmony support and it's a known issue!

My intention to test the IRSS was to use MCE mode. The imon hardware & software has a problem with disconecting from AC Power and I disconect the whole System (htpc, TV, Amplifier,...) with a IR-IF Converter via harmony for IF-sockets.

This info is from Soundgraph Support:

The feature 'power on by remote' is performed in F/W code. And the remote control selection value (iMON PAD or MCE) in iMON Manager is stored in F/W.
And the F/W compares the coming IR signal to the PAD power button if iMON PAD is selected and to the MCE power button if MCE is selected.

The default value of the remote control selection is iMON PAD and it is reset to default when AC power is disconnected. Because of this reason, after disconnecting PC from Power after shutdown, only iMON PAD remote's power button can wake up the PC.

I could solve this with the Harmony, because it can mange both configurations. But unfortunatly, neither the MCE, nore ImonPad comands are accepted, after rebooting the system that was disconected from AC before. This is a software problem in my opinion!

If IRSS can handle Imon in MCE Mode, I will give it a try (if Soundgraph has now faster solution ).

 

[disaster123]

here are my logs of my non working HID Device.

 

[belcom]

here are my logs of my non working HID Device.

I've never seen such codes from an iMON HID before.
Sry, but I assume you hounted the wrong device!

Can you please post the vendor- and productID?

 

[disaster123]

belcom
mhm i'm shure this must be the correct device but here are the details.
I've five devices comming from SG:
1.) HID konformes Gerät (HID\VID_15C2&PID_0036&REV_0002&MI_01, HID\VID_15C2&PID_0036&MI_01)
2.) USB-HID (Human INterface Device) (USB\VID_15C2&PID_0036&REV_0002&MI_00, USB\VID_15C2&PID_0036&MI_00)
3.) USB-HID (Human INterface Device) (USB\VID_15C2&PID_0036&REV_0002&MI_01, USB\VID_15C2&PID_0036&MI_01)

And then two another devices one under Mouse (HID Mouse) and then one under Keyboard (HID Keyboard).

I monitored the first one - which is the child of 3. one in Bus Hound.

 

[belcom]

@belcom
mhm i'm shure this must be the correct device but here are the details.
I've five devices comming from SG:
1.) HID konformes Gerät (HID\VID_15C2&PID_0036&REV_0002&MI_01, HID\VID_15C2&PID_0036&MI_01)
2.) USB-HID (Human INterface Device) (USB\VID_15C2&PID_0036&REV_0002&MI_00, USB\VID_15C2&PID_0036&MI_00)
3.) USB-HID (Human INterface Device) (USB\VID_15C2&PID_0036&REV_0002&MI_01, USB\VID_15C2&PID_0036&MI_01)

And then two another devices one under Mouse (HID Mouse) and then one under Keyboard (HID Keyboard).

I monitored the first one - which is the child of 3. one in Bus Hound.

I always hounted directly on USB-Bus, maybe that makes a difference... so please try the 3rd device in your list!
Thank you for helping us with your logs

 

[disaster123]

OK will do this at 5pm MET