This document is ALPHA and slammed together in 15 minutes after a week of playing around with MediaPortal, so please, correct me where I am wrong.
If you have any questions or comments, they would be more than welcome.
I thought I start this of as it seemed missing to me (having to spend a week ).
This is a HOW-TO configure mediaportal in the (my experience) best way.
The result of this config will bring you:
- Extremely wide variety of codec support, thanks to ffdshow.
- 5.1 Sound on 6 channel audio (and everything between that and stereo).
- Dolby Surround Sound on 2 channel audio.
* THIS IS NEAT! It can do either Dolby Surround decoding, or simulate it with the matrix
which will always work with any stereo source. It differentiates the left and right channels and
therefore "creates the mono rear-channel". Sound really good, gives the full touch to it.
- Same audiolevel in every option of MediaPortal.
KNOWN ISSUES:
- Cannot timeshift and listen to audio-track 2 on TV3 Catalunya due
to non-standard mp2 variable bit rate
(somehow the mediaportal chokes on this, although without timeshifting it works fine).
Are you ready?
The 16 steps:
1 Install Windows (XP|MCE) SP2.
2 Use as much the generic windows drivers as possible.
* To prevent things like Standby from failing.
Microsoft knows where their software fails...
* This is especially true for USB Hybrid/DVB-T tuners.
It might be that at first the stick (atleast my Empia 2881) is not
detected. I believe that you need to install some updates after
to make it supported generic by Windows.
3 Install VGA Driver.
* This you will most probably need if you want to use Video-out for your card.
Otherwise I would advise you to stick to what Microsoft gives you.
4 Install Tuner drivers** (IF NOT GENERICALLY SUPPORTED)
* Again, if you have an Empia 2881 chip on your board, it should be generically
supported, however, you could also use the driver included (empia driver.zip).
There are drivers for 64bit and 32bit of an UNKNOWN PROVIDER some where in Taiwan?!
However, it works fine. I had to install it because the driver provided with my
Empia 2881 (Best Buy - Easy TV USB Hybrid Pro) wasn't letting me go into standby.
* Also in the directory EEPROM you can program your chipset of the Empia 2881,
you shouldn't need to touch this and, BE WARNED!!! YOU CAN DESTROY YOUR DEVICE!!!
WATCH OUT WHAT YOU DO WITH IT IF YOU DO SOMETHING WITH THIS!!!!
5 Install KB888111 (IMPORTANT!).
* If you want 5.1 sound to work generically, you will need this, without it you'll
get stuck with 6 channel stereo instead of real 5.1 sound.
6 Configure your speaker config.
* Go to Start -> Control Panel -> Sound and Audio Devices. Click "Advanced..." in
the "Speaker Settings" Area. In the Dropdown box "Speaker setup" select 5.1 surround.
Click OK, OK.
7 Download and install Windows Media Player 11.
* http://www.microsoft.com/windows/windowsmedia/download/AllDownloads.aspx?displang=en&qstechnology=
This is just to make sure you have all the Windows Media Codecs.
8 Install and Configure Matroska splitter: http://haali.cs.msu.ru/mkv/
* Enable all the checkboxes in the menu so that it will also split avi's.
9 Install MediaPortal v0.2.2
10 Install MediaPortal SVN
10.5 UNREGISTER ALL OTHER MP2/MP3/AC3 Codecs!!!
* Start -> Run... -> cmd<enter>
* unregsvr32 /u %windir%\system32\mpadecfilter.ax
- Should return succes
* unregsvr32 /u %windir%\system32\mpegaudio.dll
(These are only the ones that come with mediaportal, so if you have others installed then you must REMOVE THEM, this is very important! If you don't; you might up with channels without sound!)
11 Download and Install ffdshow codec.
* This is the magic of having the same audiolevel in every single item in mediaportal.
Which was the worst to get right. You can download ffdshow from:
http://www.free-codecs.com/download/FFDShow.htm
12 Install libvorbis codecs: http://www.illiminable.com/ogg/downloads.html
* You need this if you want to be able to stream Vorbis/OGG of the web
I noticed that libavcodec nor tremor is able to do this in ffdshow.
13 Configure MediaPortal
* DVD -> DVD Codec
- Video Codec: Whatever you wish (NOT ffdshow! bad idea!)
- Audio Renderer: Default DirectSound
- Audio Codec: ffdshow Audio Decoder.
(Can't select it? -> download the latest version)
- Switch off the lower checkboxes (AC3Filter and DxVA).
* Movies -> Movie Player
- Video codec: (any, but I selected) ffdshow Video Decoder.
- Audio codec: ffdshow audio decoder
- Audio renderer: Default DirectSound
* Music
- Player: Internal dshow Player.
- Sound Device: Any...
* Television
- Video Decoder: Any...
- Audio Decoder: ffdshow audio decoder
- Audio Renderer: Default DirectSound
* Configure your capture card
This is the relative easy part. Make sure you are using the right drivers for the card.
I won't go further in detail on this. I do have the XML for setting up my 2881 stick
with several drivers, so if you want it, please mail me.
* This next step is a hack!!
* with notepad open C:\Program files\Team Mediaportal\Mediaportal\MediaPortal.xml
- Search for: <section name="audioplayer">
- then search for: <entry name="sounddevice">
- then change whatever is between <entry name="sounddevice"> and </entry> to:
ffdshow audio decoder
!! This is needed to make sure that ffdshow always passed through the filter chain,
even if it does not have the codec to decode the audio inside.
14 Configure ffdshow
* Go to the ffdshow audio decoder configuration.
* Enable all the codecs under "Codecs" except Vorbis.
* Set MP1, MP2 to use mp3lib.
- WHY? If encountered a channel in Spain (TV3 Catalunya) that
is sending mp2 variable bitrate on channel 2 (original version)?!
Although its out of standard, mp3lib will play it.
Enable the following filter:
- Equalizer (if needed)
- Mixer
- Volume
15 Start Windows Media Player and play 6_channel_ID.wma (included here)
* This should identify each speaker SEPERATELY, if it is not identified seperately
something is wrong. Check the forums here for answers, they are there.
Most probably however, it will be that you didn't install KB888111 yet(step 5), or you
didn't set up the sound config in windows as described in step 6.
16 Start MediaPortal
!! Make sure you don't have it enabled in always on top mode in the general tab !!
* Now play 6_channel_ID.wma in Mediaportal.
- Still identifying the speakers correcly? -> Yes.
- Is the FF icon of ffdshow in the taskbar when you play the file? -> Yes.
- Great!
* Start your television.
- If all has gone well you now have an icon in your taskbar saying FF.
- Double click the FF icon
Equalizer:
* if needed, I had to remove some bass.
Mixer:
* Enable "Normalize Matrix"
* Adjust the Voice, Surround and LFE to your needs.
- I used this to make a good general balance.
Best way I found was playing a DVD (Lord of the Rings) and edit the settings
on the fly while playing. Take something obvious in the choosing your scene
like fireworks coming towards you etc..
Volume:
* Enable "Normalize" so things don't distort and configure to your needs while checking.
- I used this to balance out the sound to compensate for the locaiton of my speakers.
Best way is to listen to a good quality mp3/ogg.
* Do this for each item (music, television, dvd and movies) until your settings
sound well everywhere.
17 You're done!
Hope this helps some people out there struggeling...
Kind regards,
Bjorn
PS Directvobsub for subtitles is adviced. Looks better than the ffdshow version.
If you have any questions or comments, they would be more than welcome.
I thought I start this of as it seemed missing to me (having to spend a week ).
This is a HOW-TO configure mediaportal in the (my experience) best way.
The result of this config will bring you:
- Extremely wide variety of codec support, thanks to ffdshow.
- 5.1 Sound on 6 channel audio (and everything between that and stereo).
- Dolby Surround Sound on 2 channel audio.
* THIS IS NEAT! It can do either Dolby Surround decoding, or simulate it with the matrix
which will always work with any stereo source. It differentiates the left and right channels and
therefore "creates the mono rear-channel". Sound really good, gives the full touch to it.
- Same audiolevel in every option of MediaPortal.
KNOWN ISSUES:
- Cannot timeshift and listen to audio-track 2 on TV3 Catalunya due
to non-standard mp2 variable bit rate
(somehow the mediaportal chokes on this, although without timeshifting it works fine).
Are you ready?
The 16 steps:
1 Install Windows (XP|MCE) SP2.
2 Use as much the generic windows drivers as possible.
* To prevent things like Standby from failing.
Microsoft knows where their software fails...
* This is especially true for USB Hybrid/DVB-T tuners.
It might be that at first the stick (atleast my Empia 2881) is not
detected. I believe that you need to install some updates after
to make it supported generic by Windows.
3 Install VGA Driver.
* This you will most probably need if you want to use Video-out for your card.
Otherwise I would advise you to stick to what Microsoft gives you.
4 Install Tuner drivers** (IF NOT GENERICALLY SUPPORTED)
* Again, if you have an Empia 2881 chip on your board, it should be generically
supported, however, you could also use the driver included (empia driver.zip).
There are drivers for 64bit and 32bit of an UNKNOWN PROVIDER some where in Taiwan?!
However, it works fine. I had to install it because the driver provided with my
Empia 2881 (Best Buy - Easy TV USB Hybrid Pro) wasn't letting me go into standby.
* Also in the directory EEPROM you can program your chipset of the Empia 2881,
you shouldn't need to touch this and, BE WARNED!!! YOU CAN DESTROY YOUR DEVICE!!!
WATCH OUT WHAT YOU DO WITH IT IF YOU DO SOMETHING WITH THIS!!!!
5 Install KB888111 (IMPORTANT!).
* If you want 5.1 sound to work generically, you will need this, without it you'll
get stuck with 6 channel stereo instead of real 5.1 sound.
6 Configure your speaker config.
* Go to Start -> Control Panel -> Sound and Audio Devices. Click "Advanced..." in
the "Speaker Settings" Area. In the Dropdown box "Speaker setup" select 5.1 surround.
Click OK, OK.
7 Download and install Windows Media Player 11.
* http://www.microsoft.com/windows/windowsmedia/download/AllDownloads.aspx?displang=en&qstechnology=
This is just to make sure you have all the Windows Media Codecs.
8 Install and Configure Matroska splitter: http://haali.cs.msu.ru/mkv/
* Enable all the checkboxes in the menu so that it will also split avi's.
9 Install MediaPortal v0.2.2
10 Install MediaPortal SVN
10.5 UNREGISTER ALL OTHER MP2/MP3/AC3 Codecs!!!
* Start -> Run... -> cmd<enter>
* unregsvr32 /u %windir%\system32\mpadecfilter.ax
- Should return succes
* unregsvr32 /u %windir%\system32\mpegaudio.dll
(These are only the ones that come with mediaportal, so if you have others installed then you must REMOVE THEM, this is very important! If you don't; you might up with channels without sound!)
11 Download and Install ffdshow codec.
* This is the magic of having the same audiolevel in every single item in mediaportal.
Which was the worst to get right. You can download ffdshow from:
http://www.free-codecs.com/download/FFDShow.htm
12 Install libvorbis codecs: http://www.illiminable.com/ogg/downloads.html
* You need this if you want to be able to stream Vorbis/OGG of the web
I noticed that libavcodec nor tremor is able to do this in ffdshow.
13 Configure MediaPortal
* DVD -> DVD Codec
- Video Codec: Whatever you wish (NOT ffdshow! bad idea!)
- Audio Renderer: Default DirectSound
- Audio Codec: ffdshow Audio Decoder.
(Can't select it? -> download the latest version)
- Switch off the lower checkboxes (AC3Filter and DxVA).
* Movies -> Movie Player
- Video codec: (any, but I selected) ffdshow Video Decoder.
- Audio codec: ffdshow audio decoder
- Audio renderer: Default DirectSound
* Music
- Player: Internal dshow Player.
- Sound Device: Any...
* Television
- Video Decoder: Any...
- Audio Decoder: ffdshow audio decoder
- Audio Renderer: Default DirectSound
* Configure your capture card
This is the relative easy part. Make sure you are using the right drivers for the card.
I won't go further in detail on this. I do have the XML for setting up my 2881 stick
with several drivers, so if you want it, please mail me.
* This next step is a hack!!
* with notepad open C:\Program files\Team Mediaportal\Mediaportal\MediaPortal.xml
- Search for: <section name="audioplayer">
- then search for: <entry name="sounddevice">
- then change whatever is between <entry name="sounddevice"> and </entry> to:
ffdshow audio decoder
!! This is needed to make sure that ffdshow always passed through the filter chain,
even if it does not have the codec to decode the audio inside.
14 Configure ffdshow
* Go to the ffdshow audio decoder configuration.
* Enable all the codecs under "Codecs" except Vorbis.
* Set MP1, MP2 to use mp3lib.
- WHY? If encountered a channel in Spain (TV3 Catalunya) that
is sending mp2 variable bitrate on channel 2 (original version)?!
Although its out of standard, mp3lib will play it.
Enable the following filter:
- Equalizer (if needed)
- Mixer
- Volume
15 Start Windows Media Player and play 6_channel_ID.wma (included here)
* This should identify each speaker SEPERATELY, if it is not identified seperately
something is wrong. Check the forums here for answers, they are there.
Most probably however, it will be that you didn't install KB888111 yet(step 5), or you
didn't set up the sound config in windows as described in step 6.
16 Start MediaPortal
!! Make sure you don't have it enabled in always on top mode in the general tab !!
* Now play 6_channel_ID.wma in Mediaportal.
- Still identifying the speakers correcly? -> Yes.
- Is the FF icon of ffdshow in the taskbar when you play the file? -> Yes.
- Great!
* Start your television.
- If all has gone well you now have an icon in your taskbar saying FF.
- Double click the FF icon
Equalizer:
* if needed, I had to remove some bass.
Mixer:
* Enable "Normalize Matrix"
* Adjust the Voice, Surround and LFE to your needs.
- I used this to make a good general balance.
Best way I found was playing a DVD (Lord of the Rings) and edit the settings
on the fly while playing. Take something obvious in the choosing your scene
like fireworks coming towards you etc..
Volume:
* Enable "Normalize" so things don't distort and configure to your needs while checking.
- I used this to balance out the sound to compensate for the locaiton of my speakers.
Best way is to listen to a good quality mp3/ogg.
* Do this for each item (music, television, dvd and movies) until your settings
sound well everywhere.
17 You're done!
Hope this helps some people out there struggeling...
Kind regards,
Bjorn
PS Directvobsub for subtitles is adviced. Looks better than the ffdshow version.